Jump to content
SAU Community

Question For R34 Gtr Vspec Owners

im late
 Share

Recommended Posts

im late Proficient

im late

Posted
Posted

I went to a import dealer today to look at a 1999 R34 GTR Vspec they have for sale.

The dealer stated to me that during compliance, the intake and exhaust gas temp gauges are disabled on the multi function display.

However he said that they can be re-enabled.

My questions are:

1. Did your Australian complianced Vspec have these two functions disabled?

2. If they where were you able to re-enable them?

3. If you did, how was it done?

Anyone out there kind enough to reply with some info is greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/310891-question-for-r34-gtr-vspec-owners/
Share on other sites
99 GTT Rising Star

99 GTT

Posted
Posted (edited)

hmmm Never heard of them being disabled, and for what reason?

Is it realy a vspec? did it have the sensor in the intercooler?

You could run a check of the vin on Nissan fast or check if the the sensor is in place or run the diagnostics on the mfd.

Diagnostic mode

1) Turn the key to the "OFF" position

2) Push and hold the joystick

3) Turn the key to the "ON" position while still holding down the joystick

4) Release the joystick at least 1 second after the "GT-R logo" appears.

5) Click the joystick 5 times within the next 3 seconds.

This will show all the working sensors and if the are in the car and connected they will show up. (note: some need to reach operating temp before they work)

Good to see your checking sounds a little dodgy to me...

Edited by 99 GTT
mxfly Veteran

mxfly

Posted
Posted

Wow, I've never heard of that excuse before. Very creative but it's pure and simple, it's total bollocks. Our raws workshop comply R34 GT-R's including V Spec's and the simple answer is no, we dont disconnect those sensors. It has absolutely no purpose to disconnect them, unless the dealer is trying to sell you a car that's not what is claimed to be.

im late Proficient

im late

Posted
  • Author
Posted
Wow, I've never heard of that excuse before. Very creative but it's pure and simple, it's total bollocks. Our raws workshop comply R34 GT-R's including V Spec's and the simple answer is no, we dont disconnect those sensors. It has absolutely no purpose to disconnect them, unless the dealer is trying to sell you a car that's not what is claimed to be.

Seeing as you are a RAWs workshop then I will take your word for it (I won't mention your name to the dealer).

I only had a quick look at the car today so I did not have time to inspect it properly or even turn it on yet/test drive/etc..

At least I know it is a V-Spec (I checked with nissan FAST) but I am a bit put off by the dealers comment about disabling it.

I will do a full investigation and report here once I do.

mxfly Veteran

mxfly

Posted
Posted

You are more than welcome to name our workshop as I know we are adhering to the rules.

Also with the vin number, just double check their details with the ones that are actually on the car. The plaque is located on the firewall, if I remember correctly.

UnCo Rising Star

UnCo

Posted
Posted (edited)
Diagnostic mode

1) Turn the key to the "OFF" position

2) Push and hold the joystick

3) Turn the key to the "ON" position while still holding down the joystick

4) Release the joystick at least 1 second after the "GT-R logo" appears.

5) Click the joystick 5 times within the next 3 seconds.

This will show all the working sensors and if the are in the car and connected they will show up. (note: some need to reach operating temp before they work)

Good to see your checking sounds a little dodgy to me...

I went in to diagnostic mode just to have a play around because I was curious.

After doing so, I found that I had lost my exhaust and intake temp display as well!

As mentioned above, the sensors need to be reactivated so for something such as exhaust temp you'll need to be in diagnostic mode and drive until the exhaust temp hits the minimum (400 degrees) before the sensor will be showing as active again.

Below is a picture of the screen after I went in to it and some functions weren't showing up as working.

You'll need to enter diagnostic mode with the engine on to try to reactivate these things.

This is a bit difficult to get the timing right because step 3 of the instructions is to go from OFF to ON while holding the joystick in.

To get in to diagnostic mode with the engine on, I had to time it right so that I pressed the joystick in during the time the car cranked over (and the power to the screen cuts out). Hope you understand what I mean..

th_MFD.jpg

So once the engine is on and you're in diagnostic mode still, you can start reactivating the greyed out sensors.

Eg. Speed, exhaust, F-torque, F/R and L/R G forces, brake..

And done!

th_MFD1-1.jpg

Usually, a quick drive down the street will bring the exhaust temp high enough to get to 400 degrees.

I thought I could do it by sitting in my driveway holding the revs up but it was taking too long haha.

I hope this helps in some way!

Oh and also as mentioned, those sensors don't get disabled during compliance.

My guess is someone went in to diagnostics to play around and couldn't figure out how to reactivate it.

Edited by UnCo
  • 2 weeks later...
silva33 Mentor

silva33

Posted
Posted

I just tried this with my V-Spec, i managed to turn off the bottom two sensors and shit myself because I couldnt get them back on! After a while of stuffing around I figured it out.

So the sensors may just be turned off but I wouldnt have believed it if I had not tried it myself.

silva33 Mentor

silva33

Posted
Posted

You need to use the functions to activate them, so when you have started the car in the diagnostic mode take it for a 5 min drive and you will see all of the items light up by themselves.

I was stressng out when I turned mine off as I couldnt turn them back on, but you will see for example, when you his the brakes, the brake light will illuminate on the MFD.

  • 5 weeks later...
slmawi Newbie

slmawi

Posted
Posted

hello

i have r34 gtr v-spec 2002

it's happen to me today and can't back it

i was play around Diagnostic mode and after that i lost the bottom sensor and can't work any more

i try to get Diagnostic mode but i can't not work with me any more !! why

and AWD and LSD not work as well after rebuild the engine may be tps need reprograme ? when hit i get 96% and i lost oil pressure sensor too sowed 0 and go to 1 and stop

i hate the car now no thing work !!

any body have same problem ad can't get Diagnostic mode

UnCo Rising Star

UnCo

Posted
Posted (edited)

Duckyys, AFAIK the G-Meter is on the Nismo MFD?

I actually only found that out when I hopped in another GT-R and realised it didn't have it whereas mine did.

Diagnostic mode

1) Turn the key to the "OFF" position

2) Push and hold the joystick

3) Turn the key to the "ON" position while still holding down the joystick

4) Release the joystick at least 1 second after the "GT-R logo" appears.

5) Click the joystick 5 times within the next 3 seconds.

To get in to diagnostic mode with the engine on, this is what I did.

- Key in the ON position but engine off still.

- Turn the key to START the car. In the split second the power to the screen turns off, press and hold the joystick in.

- When the GT-R logo sppears, click the joystick 5 times within 3 seconds.

It might take a few tries at this to work because the timing of pushing the joystick when the screen is off has to be right.

Once you are in diagnostic mode with the engine turned on, drive up and down the street until all the sensors have turned green.

To recalibrate the TPS follow these instructions.

1. Turn the key to the OFF position.

2. Press and hold "RETURN" and "MODE" buttons at the same time.

3. Turn the key to the ON position while still holding down RETURN and MODE buttons.

4. When the GT-R logo appears, release the RETURN and MODE buttons and click the joystick 5 times within 3 seconds.

You will then enter the calibration for TPS.

It will be in Japanese, but the first screen asks you to have 0% throttle and press the joystick.

Then it will ask you to hold 100% throttle and press the joystick.

Then it will show you a guage to confirm.

Turn off the car to exit.

Edited by UnCo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...