Jump to content
SAU Community

Recommended Posts

Just curious where everyone has the amps mounted in their R34's?

I thinking of putting them in the boot above the petrol tank but interested in other opinions

you can put them there,but make sure you can still get to the wires etc on the fuel pump if it dies and dont drill into the floor = fueltank , or behind the side panels there is heaps of room, but you better know how to mount them without denting or piercing the outside metal skin. and then you can hide them completely

or false floor above spare tyre. don't recommend ditching the spare for audio gear unless its a show car only

side panels in rear seat area has a bunch of room behind the "flux capacitor" panels(the one with all the bolts holding them on..lol) but stear clear of seat belt pre-tensioners on the reels. (yellow wires)

under front seats, not a real good spot on that car

depends on size,heat, your goal, to hide them or show them off, expense to do right, skills if you do it yourself ? lots of factors

My mate and I made up a false backing from MDF then carpeted it, and drilled out holes for the wiring where the step at the back of the boot is to mount the amp to. Was alot of work but it worked out well as it looks neat, is out of the way and hides most of the wiring

This is it:

post-44229-1268209468_thumb.jpg

post-44229-1268209540_thumb.jpg

see the bolt in the upper left corner, it screws into the metal bracket behind the carpet cover

and scotty doo I hope that fuse isn't the one for the battery . you do have one up front very near the battery don't you ??? if not your asking for a massive car fire(unless your battery is in the back of the car now ?) you don't have to give up so much space. the amp can get a lot closer to the seat back , but don't put the power wires too near the computers in the back if you can help it.

see the bolt in the upper left corner, it screws into the metal bracket behind the carpet cover

and scotty doo I hope that fuse isn't the one for the battery . you do have one up front very near the battery don't you ??? if not your asking for a massive car fire(unless your battery is in the back of the car now ?) you don't have to give up so much space. the amp can get a lot closer to the seat back , but don't put the power wires too near the computers in the back if you can help it.

You're right we bolted the MDF board at the top on either side, and the bottom of the board sits behind the lip on the step. The two bolts hold it in very securely, and is easy to take out.

Yes the fuse is the one for the battery and the battery is in the engine bay still. Thanks for pointing this out, we were going to put it in the engine bay orignially but decided to put it in the boot for aesthetic reasons, but didnt think about it enough obviously. We'll be putting one in the engine bay now too very soon. :P

On the use of space, I've found where it is to be pretty good actually. I never used the shelf part of the boot anyway and the amp doesnt stick out very much at all beyond that point. I could have mounted the amp on the inside of the board but I wanted to show it off a little. And the Sub is really quick and easy to grab out too if I need the space. Putting the board back any further would have just made things so much more difficult and time consuming it just didnt make sense for a nothing space. The gap behind it is good for hiding the extra length of wiring too. And none of it is anywhere near the computer gear for the car either.

Cheers.

On mine I only have 1 bracket in the middle that holds the carpet and it seems pretty flimsey

there is a pretty thick steel plate , between the front and rear part of the car. on coupes to stiffen the chassis , weighs a bunch but does help a lot for rear stiffness. pull out your rear seat you can see it and access the bolts to it. also there is a lot of bolt down holes along the rail near it. 10mm bolts

if you want to hang a bracket off it. or you can look up under the rear deck, a few spots to hang a metal bracket down to secure a amp rack.or epoxy a bracket on the floor if you don't want to drill for fear of fuel tanks, brake lines, etc. ? I would hang a amp inside the rear panels to hide it and still have cooling, and you can mount a up to 12" sub on either side , behind the panels as well. without major drama or hacking

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...