Jump to content
SAU Community

General Meeting Pre-meet For Westies 16/3/10

Halle

By Halle,
in Archived Events

 Share

Recommended Posts

Halle Community Regular

Halle

Posted
Posted

General Meeting is for everyone (yes even if you are not a paid/finacial member)

Where: Ring Road Macca's Inbound, Ardeer (mobil servo)

When: Tuesday

Meet: 6:45pm

Leaving: 7:30pm

Destination: Bells Hotel, 157 Moray St, South Melbourne (Cnr Moray St & Coventry

St Melways Ref - 57, G1)

hope to see you all there

alr33x Grand Master

alr33x

Posted
Posted

yehhh ill be there unless im working late..

thats a long pre meet man id shrink it down otherwise you'll get stragglers might get boring if u get there say 6.45 waiting 45 minutes for people that may or may not show up..

maybe pm ur number to attendee's incase they are held up... thats were i fkd up with mondays pre meet had car trouble but couldnt let ppl i didnt know know..

alr33x Grand Master

alr33x

Posted
Posted
i'll be the from 6.45 ppl usually rock up whn ever. leavin on the dot thou.

yeh ill pm my number whn the list themselves as coming.

what wrong with ya car?

nah was just a flat battery so all good :nyaanyaa:

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...