Jump to content
SAU Community

Recommended Posts

:(list of some parts and standard items i wish to sell from build-up :worship:

- standard radiator from s2 R33 RB25DET excellent condition $150 SOLD

- standard s2 R33 RB25DET block no head, block is in excellent condition, $800 SOLD

- Gizzmo IBC Electronic Boost Controller excellent condition comes with everything $250

- standard in-tank fuel pump s2 R33 very good condition $50 SOLD

- s2 R33 RB25DET auto-trans + pedals excellent condition stage 2 shift kit been serviced new filter trans-fluid etc from mike at M.V. automatics $500ono

- s2 R33 RB25DET impul auto ecu removes speed limit cut rev limiter goes to 7.200rpm i think been awhile since i have been on the dyno give or take boost cut removed or moved i was running 14.3psi excellent condition $200

- 2x standard boost solenoids good condition $15 each

- s2 R33 whole complete A/C from the engine bay ill check with my mechanic excellent condition $400ono

1 x Brand New Blue Castor Rod Bushes noltec or nolethane $65 pick-up or $70 posted.

1 x complete set off standard R33 s2 brake lines front + rear used but in fine condition no splits kinks etc $50 pick-up or $55 posted.

2 x standard R33 rims good for drifting etc camber wear on tread $70 pick-up only.

................................................................................

.................................................................................

...........................

measurements in INCHES for thermal flex left overs...

1 x Thermal Flex (RED) 8" long X 2" wide------------------------ $15

1 X Thermal Flex (BLUE) 6" 1/2" long X 2" 1/2" wide------------ $15 ------------$60 for all 3 pick-up or $65 posted

1 x Thermal Flex (BLUE) 13" Long x 3" Wide--------------------- $30

................................................................................

.................................................................................

.............................

1 x i believe its the heater unit minus the heater core $60 pick up or $70 posted.

1 x i got this from a group buy a while back black faced 300km/h speedo set in psi no 300km/h tho i have it in my car but i put the 180km/h speedo with the set, boost gauge on tachometer is in psi and oil pressure is in psi as-well + new hot/cold gauge and fuel level so everything except the 180km/h is new the set cost me $100 + postage so i guess it would be fair to ask for $50 pick-up or $55 posted.

1 x 1996 s2 R33 rb25det Throttle body good condition $60 pick-up or $65 posted

1 x R33 Skyline Standard Genuine Nissan Dump Pipe $30 pick-up or $35 posted

1 x R33 s2 Skyline nissan genuine rubber intake pipe used, good condition no perishing, comes with stock BOV plumb back hose $50 pick-up or $55 posted

1 x s2 R33 Cross Over pipe with b.o.v. $55 pick-up or $60 posted

1 x R33 s2 Original Nissan intake manifold (plenum) comes with top and bottom half rubbers, bolts, everything needed to fit it up., no cracks or leaks, reason for sale is put greddy intake on. $75 pick-up

6 x s2 R33 GTST 370cc injectors, all working when taken out of car, just been removed for nismo injectors these have only just been taken out and are all in 100% working and flowing condition!! comes with rail. $150 pick-up or $155 posted.

most items can be posted some cant...

contact me on here or e-mail me at ([email protected]) or call me on (0401409575Allan)

i will start uploading some pictures tonight if i have got some time..

All items located in : Adelaide,SA

Contact me on (0401409575 Allan) or pm-me parts can be delivered via freight/courier at your expense or pick up in Adelaide,SA parts are with my mechanic so can organize it any-time.

most prices are negotiable.!

Regards.

Allan.M

1 x R33 s2 Skyline nissan genuine rubber intake pipe used, good condition no perishing, comes with stock BOV plumb back hose $50 pick-up or $55 postedSOLD

1 x Thermal Flex (RED) 8" long X 2" wide------------------------ $15

1 X Thermal Flex (BLUE) 6" 1/2" long X 2" 1/2" wide------------ $15 ------------$60 for all 3 pick-up or $65 posted SOLD

1 x Thermal Flex (BLUE) 13" Long x 3" Wide--------------------- $30

- s2 R33 RB25DET impul auto ecu removes speed limit cut rev limiter goes to 7.200rpm i think been awhile since i have been on the dyno give or take boost cut removed or moved i was running 14.3psi excellent condition $200 SOLD

- s2 R33 RB25DET impul auto ecu removes speed limit cut rev limiter goes to 7.200rpm i think been awhile since i have been on the dyno give or take boost cut removed or moved i was running 14.3psi excellent condition $200 SOLD

back up for sale due to time waster

................................................................................

................................................................................

.

...........................

measurements in INCHES for thermal flex left overs...

1 x Thermal Flex (RED) 8" long X 2" wide------------------------ $15

1 X Thermal Flex (BLUE) 6" 1/2" long X 2" 1/2" wide------------ $15 ------------$60 for all 3 pick-up or $65 posted

1 x Thermal Flex (BLUE) 13" Long x 3" Wide--------------------- $30

................................................................................

................................................................................

.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The trigger kit I have is similar to the one in the link below. While going through Facebook, I saw someone else mention a similar issue, and I’m starting to think this could be related to the crank gear itself. I understand these parts are CNC machined, but maybe some earlier versions or individual pieces might have slight inconsistencies—it just doesn’t look right in my case. https://www.facebook.com/share/16an8evZd9/?mibextid=wwXIfr I originally installed the crank gear using the thin OEM washer, but as shown in the attached photo, the timing belt walks very close to the edge. When I tried using a Nitto washer—which is thicker—it actually made the issue worse. The belt walks about 1mm off the front edge, which raises more concern about alignment.   I’ve gone through the full process of elimination:   The tensioner pulley and bolt are brand new and installed correctly. The bolt isn’t bent and is oriented properly. The back of the tensioner and the idler pulley are clean and seated correctly. The idler sits slightly more forward, which I understand is due to its design. I’ve experimented with both tight and loose belt tension, but it makes no difference. As soon as the engine runs, the belt immediately walks forward again—even if I reset it beforehand.     At this point, I’m considering replacing the crank gear with your Race Version 1 (12-tooth), but before purchasing, I wanted to ask:   Are you aware of any alignment issues when using this gear? Would this gear help keep the belt aligned correctly, or could the walking still occur? Does it work with a standard missing-tooth crank and rear washer? Is there any specific crank setup or install procedure required?     For reference, I’m not using a front washer, as the PRP crank gear seems to replace the need for one.   Looking forward to your advice.
    • Yep, looks that way. Never driven an E30 or R31 so I can only imagine  
    • Yuh, My new R34 box is sitting on the workshop floor (in its large shipping box, which is a nice thing on its own), along with a front plate to convert to push clutch. There was no way I was interested in rebuilding my existing one. Was only partly interested in the risk of buying a used one. But, if you want a 2nd hander, I can point you to one in/near Melbourne at least. @Komdotkom has one that should be in good enough condition to be usable. I don't think it's in a for sale thread, you'd have to message him. @redzedhas one that definitely needs a rebuild.
    • I used to love going to Amaroo to watch the HQ series go for broke (eventually stopped due to lack of spare parts) and also the Porsche series.  It was so cool to back your car up to nearly the edge of the viewing barrier and party with your friends, having a bbq and alcoholic/non drinks. It was such a family/mates atmosphere
×
×
  • Create New...