Jump to content
SAU Community

Recommended Posts

6x9 don't fit in the front, despite all my effors. Put 6.5" in front on mine. Mange to fit 7x10 in the back on mdf, with out modifiying the parcel tray. It just clears the window.

Yeah make all your mounts on MDF, cus it won work other wise. Well depends how much metal u might want to cut in some instances.

  • 3 weeks later...
  • 1 month later...

I've just tried to fit 6.5" speakers to the front doors of my R32 and they won't fit behind the factory grille.

Are there any tricks I might have overlooked?

They are 62mm deep plus they need 14mm clearance in front to clear the suuound, 76mm total depth. There is 68mm between the window mechanism and the top edge of the factory grille so they are 8mm too big.

How deep are the 6.5" speakers that people on here have fitted successfully?

How are you mounting the speeaker? Are you just mounting thwem to the metal door? I would suggest using 18mm mdf as a backing board then putting the speaaker onto that. Dont worry about putting the speakers speaker grill on it.. not needed when it is being proteected by the door grill. Give that a try, you will find it will work. Heck, if i can fit a 4inch and a 5.25 inch in a 4inch speaker fitment, anything can be done.

Quote mtopxsecret6

"How are you mounting the speeaker? Are you just mounting thwem to the metal door? I would suggest using 18mm mdf as a backing board then putting the speaaker onto that. Dont worry about putting the speakers speaker grill on it.. not needed when it is being proteected by the door grill. Give that a try, you will find it will work. Heck, if i can fit a 4inch and a 5.25 inch in a 4inch speaker fitment, anything can be done."

Thanks for your reply.

I made a baffle and mounting ring to fiberglass at the correct angle with the speaker magnet as far back as possible but when I checked the clearances by refitting the door trim the top edge of the factory grille touched the speaker surround which needs 8mm of clearance during operation. The space is physically 8mm too small for this speaker to fity behind the factory grille.

Quote Fhrx

"The R32 skyline will happily take 6" speakers in the front doors."

Not my 160GTs but then they're 6.5s" I don't regret my choice of driver. I'll make it fit. Then again if I have to make a custom buildout I may as well fit my MW170s.

I just wanted to know how other people have approached this job in the R32s.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes to both! Yes to standard ECU and tune, but exhaust is aftermarket. Unsure on brand. Actually have it sitting in at my desk haha! I have to set it up on my laptop but this is a great next step, will do. So I generally try to shift before 4.5K RPM most times. I largely don't do a lot of high-rev driving, but I will take it up to red 1-2x a week max, as I know the occasional "Italian tune-up" is good for these cars.  Oh wow, is this way better than what I'm getting. Does this mean there's a good chance I have an issue?   Thanks for all the info so far guys.
    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
×
×
  • Create New...