Jump to content
SAU Community

Ebc Boost Issues

shibby69

By shibby69,
in Engines & Forced Induction

 Share

Recommended Posts

shibby69 Collaborator

shibby69

Posted
Posted

Hello,

I just installed a HDI electronic boost controller for my r32 GTST but am having issues with it.

When on boost (5k rpm) the car will cut out and make loud sounds from the exhaust. (misfire?)

The EBC was installed by an auto electrician so hopefully we can eliminate a wiring issue.

Before I installed the EBC the car was fine, boosting to correct levels.

I've attempted to change the setup back to normal. Leaving the EBC in the car but bypassing the EBC solenoid which initially fixed the problems but since has stopped working properly.

What could the issue be? Spark plugs?

I've searched the forums but can't find a matching issue to mine.

(brb flame proof suit)

Link to comment
https://www.sau.com.au/forums/topic/312355-ebc-boost-issues/
Share on other sites
StealthX Veteran

StealthX

Posted
Posted

you havnt mentioned how much boost you were/are running.

do you have a boost gauge?

are you sure theres no adjustments on the EBC?

and that it makes exactly actuator pressure before it bleeds any air off?

my moneys on its making more boost and your going R&R or too lean @ 5k rpm

also just one of those misfires etc when you first had the EBC on, would've fouled your spark plugs, now they are struggling to fire.

so new plugs as Nismoid said, then see how ya go...

shibby69 Collaborator

shibby69

Posted
  • Author
Posted

yeh thats what i was thinking, with the fouled plugs. well now it should be running stock boost cos i set it up bypassing the ebc's solenoid, when i had the ebc on the boost kept going up rapidly even tho it was on the lowest setting, it hit 14 at one stage

Cam84 Community Regular

Cam84

Posted
Posted

I also have a HDI EBC-R, i havn't had an issue with it yet. As the guys have said, more boost requires more spark etc i would change plugs and if you can't afford new coils, get some industrial grade silicone and glue them up not a total fix but will fix most probs (unless coil completely gone). Also get out on a QUIET road or more safer a dyno and get it tuned and set right, if it's boosting to 14psi when it's not ment to check all hoses at the soleniod. This was happening to me but mine hit about 16psi (Shyte), i found that one of the hoses has a slight split. If you set boost to high you may break something. (BOOM) show me the money.

my two coin

Cam

shibby69 Collaborator

shibby69

Posted
  • Author
Posted

thanks mate, yeh mine hit 16 psi yesterday after i thought id fixed it :blink: although it didnt feel like it was pushing 16 psi. i got some spark plugs will put them in on sunday. only want to run 10 or 11 psi at the moment too

I also have a HDI EBC-R, i havn't had an issue with it yet. As the guys have said, more boost requires more spark etc i would change plugs and if you can't afford new coils, get some industrial grade silicone and glue them up not a total fix but will fix most probs (unless coil completely gone). Also get out on a QUIET road or more safer a dyno and get it tuned and set right, if it's boosting to 14psi when it's not ment to check all hoses at the soleniod. This was happening to me but mine hit about 16psi (Shyte), i found that one of the hoses has a slight split. If you set boost to high you may break something. (BOOM) show me the money.

my two coin

Cam

shibby69 Collaborator

shibby69

Posted
  • Author
Posted

spark plugs fixed the misfire, but the boost controller just doesnt control the boost, it pushes past 16 psi!

runs fine if i use the same hoses but instead of going into the solenoid i just put them back into each other like an extended version of how they are normally set up, runs 11 - 12 psi though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • Duncan
      1992 R32 GT-R Race Car

      By Duncan · Posted

      heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
    • Duncan
      Oil pan for RB25DET NEO Stagea "version"

      By Duncan · Posted

      meh, it was a good video, clear about the issue and how he dealt with it. A bit heavy on the RTV and very brave to put an RB in anything without rebuilding it first, but otherwise I thought it was good Dose, I'm not sure that having the pickup forward is a big issue; yes of course the oil could shift under brakes but the sump should never be empty enough for that to be a problem (unless you also have a higher volume oil pump, and that oil can't return from the head to the sump quickly enough)
    • MBS206
      Starting again

      By MBS206 · Posted

      I can donate $100 to your upgrade fund. So long as you can donate the IC7 my way....
    • MBS206
      Starting again

      By MBS206 · Posted

      I'd love a Haltech ECU, and Haltech 10 dash. Was having a chat with Rob and Andy @ Haltech when Rob put one in his MR2. First one I'm kind of interested in too, as you can dim it RIGHT down. Andy was saying bright dashes is one of his peeves too!
×
×
  • Create New...