Jump to content
SAU Community

Recommended Posts

hey everyone!

r32 gtr stuff: (all the stuff working fine otherwise i wouldnt bother selling them.)

attesa actuator (back of gearbox thingy) $80:

biroua.jpg

2x Air flow meters $150:

dheu84.jpg

20tndoo.jpg

air box no filter $150:

2061l3c.jpg

crank angle sensor $150:

220nc7.jpg

2gyaazp.jpg

coil pack harness (a bit stiff, but still working fine)$20:

2426b61.jpg

coil packs (miss 2 rubbers) $40:

jpeusp.jpg

strut bar ( by ibs)$100:

34odi06.jpg

2lk4q9t.jpg

exhaust manifolds with heat shields $150:

23upoab.jpg

genuine nissan N1 speedo 98k on it $220. (no longer avaible from nissan)(its got a couple of scatches on it, only seen at night and can be fixed with touch up paint).

bdtaw0.jpg

fd7q02.jpg

genuine nissan oil pressure and water:

r6zhv7.jpg

alternator 80amp $120: (been reco'd before)

crq84.jpg

water feed lines $15:

148oxno.jpg

just jap oil relocator $50:( doesnt not leak with you use thread sealant)

120ksww.jpg

9x oil filters for just jap relocator adaptors $5ea or all for $40:

dgnz1x.jpg

call/sms/pm any questions or deals on 0422772841

thanks danny

Hey Buddy, interested in taking those filters off your hands. Where about in Sydney are you - or how much with post to Turramurra, 2074?

Just need to check mine tonight to make sure they are the correct number.

Thanks.

  • 2 weeks later...
  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...