Jump to content
SAU Community

Recommended Posts

hey everyone!

r32 gtr stuff: (all the stuff working fine otherwise i wouldnt bother selling them.)

attesa actuator (back of gearbox thingy) $80:

biroua.jpg

2x Air flow meters $150:

dheu84.jpg

20tndoo.jpg

air box no filter $150:

2061l3c.jpg

crank angle sensor $150:

220nc7.jpg

2gyaazp.jpg

coil pack harness (a bit stiff, but still working fine)$20:

2426b61.jpg

coil packs (miss 2 rubbers) $40:

jpeusp.jpg

strut bar ( by ibs)$100:

34odi06.jpg

2lk4q9t.jpg

exhaust manifolds with heat shields $150:

23upoab.jpg

genuine nissan N1 speedo 98k on it $220. (no longer avaible from nissan)(its got a couple of scatches on it, only seen at night and can be fixed with touch up paint).

bdtaw0.jpg

fd7q02.jpg

genuine nissan oil pressure and water:

r6zhv7.jpg

alternator 80amp $120: (been reco'd before)

crq84.jpg

water feed lines $15:

148oxno.jpg

just jap oil relocator $50:( doesnt not leak with you use thread sealant)

120ksww.jpg

9x oil filters for just jap relocator adaptors $5ea or all for $40:

dgnz1x.jpg

call/sms/pm any questions or deals on 0422772841

thanks danny

Hey Buddy, interested in taking those filters off your hands. Where about in Sydney are you - or how much with post to Turramurra, 2074?

Just need to check mine tonight to make sure they are the correct number.

Thanks.

  • 2 weeks later...
  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...