Jump to content
SAU Community

Recommended Posts

having a further read, they explain it plugs into the factory loom. and there is the option of using the standard nissan wheel.

sounds all too good to be true. if you watch the video of it in the 350z looks quite good.

maybe we can do a group buy, id like to see the kit of what comes with it and how hard it is to tap into the factory loom.

Yeah, see that Works Bell kit a bit on Yahoo Auctions.

Can't help but think that a V35 OEM paddle shift would end up cheaper, would bolt straight in (I imagine as they both have the same steering column) and looks/feels damn good too!

And found the pic of this front bar,one of the best bars I've seen in a M35 + this other one (is this color stock?)nice...very nice.

post-52922-1269825692_thumb.jpg

post-52922-1269827233_thumb.jpg

Edited by southern_tango
Yeah, see that Works Bell kit a bit on Yahoo Auctions.

Can't help but think that a V35 OEM paddle shift would end up cheaper, would bolt straight in (I imagine as they both have the same steering column) and looks/feels damn good too!

sounds like we need to do a bit of research mate. i didnt even know that you could get the paddle shift on the v35.

And found the pic of this front bar,one of the best bars I've seen in a M35 + this other one (is this color stock?)nice...very nice.

Left = Freeway/Dolphin

Right = Nismo modified with R32 intake ducts. Not sure on the grill... seen it before somewhere, just can't put my finger on where

sounds like we need to do a bit of research mate. i didnt even know that you could get the paddle shift on the v35.

Yeah, my mates V35 GT8 has the paddles. Damn nice paddles I must say.

Will get a part number if I can get FAST working today :)

it would be good if the gearbox wasnt so friggen slow at shifting. actually it would be REALLY good if it shifted quickly

True, if our trans shifted gears as quickly as the CVT trans "changed gears" (practically immediate), then the paddles would be great.

OR you could just get one of the shift kits fitted (of for guys from the other states, send down your bits, have them updated and shipped back for installation)

your right.

the change speed is a little dismal.

with that change kit and the paddles, would make it pretty good.

on the link at the very top there is a you tube clip of the kit fitted to a 350z, it changes quite well in that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...