Jump to content
SAU Community

Recommended Posts

Hi all,

I've got some bits to suit 33 gtst for sale, no photos for now but could organise some later.

1; A pair of GAB struts to suit R33 gts/t (may fit 34 as well) fronts, no leaks as far i can see. Asking $50.

2; A set of R33 (possibly fit to R34) strut tops, in fair condition. Asking $50.

3; A set of springs, I think it's aftermarket but not 100% certain, have some rust though. I'm giving these away for FREE pick up only or they're destined for rubbish bin.

4; Cat-back exhaust JASMA approved for R33 gtst, may fit into gtr but don't quote me on this. Asking $50.

All items are located at Frankston South, VIC. I can be contacted via PM or SMS on 0430 129 511.

Cheers

Grant

IMG_0008.jpg

BTW it's 3" from cat and split to 2x 2" (i think) under the diff then meet up at rear muffler.

Cheers

Grant

Exhaust is SOLD

Everything in 1st post is still available, make an offer.

Cheers

Grant

My dad is coming home tomorrow and could you help me out by purchasing items I've got for sale?

I'm negotiable, so feel free to make an offer.

Cheers

Grant

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...