Jump to content
SAU Community

Recommended Posts

Hey all

Am thinking of selling my 32 FOUR door which has had ALOT of time and $$$ Spent. At the moment it is EOI only as i am oversea's till 16th April due to work comminments.

Engine is currently being built with only the best parts. Car will be sold tuned and rego'd.

ITEM : 1990 R32 SILVER FOUR DOOR

CONDITION : BODY IS A LITTLE RUFF AS EXPECTED FOR AGE , HAS COUPLE DENTS / SCRAPES BUT NOTHING TOO SERIOUS, INTERIOR IS GOOD WITH STANDARD SEATS FRONT AND REAR AND PANELS.

MODS : OK ILL TRY REMEMBER EVERYTHING.

ENGINE ( BOTTOM END )

ENGINE WILL BE BRAND NEW AND IS HALF WAY FINISHED ( WILL BE COMPLETED IN 2 WEEKS !! )

SPEEDLAB CUSTOM RB24

EAGLE RODS

TOMEI PISTONS

ARP RACE SERIES STUDS

TOMEI RINGS

PISTONS HAVE BEEN TEFLON COATED

FRESH LINE BORE AND HONE

ACL RACE SERIES MAIN AND ROD BEARINGS

CUSTOM SUMP BAFFLES

SOLID ENGINE MOUNTS

N1 WATER PUMP

N1 OIL PUMP

ENGINE ( HEAD )

FULL RACE PORTING

JUN 272 INLET AND EXHAUST CAMS

JJR ADJUSTABLE CAM GEARS

TOMEI SPRINGS

TOMEI GUIDES

GREDDY TIMING BELT

ENGINE ( PERFORMANCE / FUN STUFF )

GENUINE HKS 25/30 ( DONE 2000KM SINCE NEW )

XSPEED JAPAN STAINLESS LOWMOUNT EXHAUST MANIFOLD

HKS DUMP ( SERIES 2 WITH LARGER GATE OUTLET )

CUSTOM EXHAUST

MICROTEC LTX12'S

CUSTOM WIRING

550cc INJECTORS

TOP SECRET FUEL REG

OS GIKEN TWIN PLATE

SPEEDLAB DRAG COOLER ( 600 X 320 X 115 )

SPEEDLAB OIL COOLER

CEFIRO CROSS MEMBER ( SITS THE ENGINE 30mm LOWER FOR BETTER GRAVITY :D )

KAAZ 2 WAY DIFF CENTRE

GTR DIFF CASING ( BETTER COOLING AND MORE OIL )

SOLID REAR FRAME BUSHES

SOLID GEAR BOX MOUNT

SOILD DIFF MOUNT

SUSPENSION

CUSCO COMP COIL OVERS

CUSCO FRONT AND REAR STRUT BARS

CUSCO BRAKE MASTER STOPPER

CUSCO REAR UPPER ADJUSTABLE ARMS

ARC CASTER ARMS

EXTRA LOCK STEERING KNUCKLES AND ARMS ( FORGOT BRAND BUT THERE JAP )

BRAKES

R32 GTR CALIPERS AND DISCS ALL ROUND

TOP SECRET BRAKE PADS

PROJECT U HYDROLIC HAND BRAKE AND CUSTOM LINES ( STILL HAS NORMAL ONE AS WELL )

BRAIDED BRAKE LINES

FUEL

BOSCH 044

CUSTOM SWIRL POT IN BOOT

NISMO INTANK PUMP

MISC

N1 HEAD LIGHTS

MOMO STEERING WHEEL

HKS BOOST GAUGE

N1 BONNET LIP

EXHAUST MANUAL CONTROL VALVE

There is more then likly a few things i have missed.

Over $30,000.00 in parts and aftermarket items has been spent on this car in the last 18 months.

Once finished there is No reason 275 - 300RWKW is not possible with this setup. Will be an awsome streeter / track drifter .

LOCATION : ADELAIDE

PRICE : $17,000.00

CONTACT : PM ME

PICS : WILL GET SOME ONCE IM BACK IN AUS

Cheers

Link to comment
https://www.sau.com.au/forums/topic/315422-eoi-insane-streeter-r32-four-door/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...