Jump to content
SAU Community

Recommended Posts

1997 R33 Series 2 125,000kms

Serviced Every 5000km or less with Motul turbo light 10w 40w

Motul Diff Oil

Redline Gearbox Oil

Modifications,

Apexi Power FC Tuned at 12psi (made 201kw)

Blitz Dual SBC boost controller

Split Fire Coil Packs

Walboro Fuel pump

Blitz turbo timer

R34 Turbo (OP6)

RB20 Wastegate Actuator (10 psi)

Split Dump/front Pipe

3in Hi Flow cat (inside not bashed out)

3.5 inch HKS Hi Power Exhaust From CAT back

Apexi Power intake filter on custom made Metal intake pipe onto the turbo

(Pod not totally boxed in but covered over see photos below)

Standard RB20 Blow off valve

Greddy Front Mount Inter cooler and piping

Alloy Radiator

Heavy Duty Excedy Clutch

Braided Clutch Line

Braided Brake Lines (ADR approved)

Master cylinder stopper

Front and Rear Strut Braces

Bilstein Shocks and King Springs

Front Whiteline adjustable Castor Bushes (adjustable on car)

Rear Whiteline Camber Bushes

Work Emotions CR KAI 18 x 8.5 in all round

235/35/18 federal 595 SS on the front (50%)

235/35/18 Sumitomo HTR Z 3 on the rear (50%)

Work blue Wheel Nuts

M Spec side skirts and rear pods

33 GTR rear seat

Have had the Roof lining, A-Pillar and B/C Pillar trims redone in Black Suede (haven't done the sun visors yet)

White LEDs' in the cluster

Have Changed the AC Panel, cigarette lighter surround and ignition barrel surround lights all to blue LEDs'

Pioneer Head Deck (DEH-P6850MP)

Pioneer Front Speakers and tweeters

Pioneer Rear 6in Speakers

And finally the rear "Skyline" Boot garnish lights up red with taillights

There is probably more little bits and pieces i have forgotten, Basically the car has never missed a beat in the last 2 years runs great, drives beautifully and handles well. Has been my pride and joy for a little over a year but its time for me to move on, Pictures Below feel free to ask any questions.

Price - $14,900 Will get RWC upon Sale

I am willing to remove some parts to bring the price down.

Plates Not Included

Brisbane QLD

PM for my contact details if you are interested

and i also have a few more photos too.

Cheers Scott

post-29410-1270853707_thumb.jpg

post-29410-1270853726_thumb.jpg

post-29410-1270853737_thumb.jpg

post-29410-1270853748_thumb.jpg

post-29410-1270853762_thumb.jpg

post-29410-1270853801_thumb.jpg

post-29410-1270853816_thumb.jpg

post-29410-1270853838_thumb.jpg

Unable to pm you as i don't have 10 posts.

Would you be able to send me more images of the interior.

For $10,500 does it come with EVERYTHING ELSE other then WORK WHEELS, POWER FC AND BOOST CONTROLLER

What condition are the stock wheels at?

Cheers

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...