Jump to content
SAU Community

Swap/trade - Racing Sparco Nt-r 17" For Stockies With Decent Tyres

180JDM
 Share

Recommended Posts

180JDM Community Regular

180JDM

Posted
Posted

Hey,

I'm wanting to get rid of these wheels and just put some stockies on while i wait for my new wheels from Japan.

I need 5x114.3 wheels, dont care what they look like but they need to clear R32/S15 brakes.

I'm not sure on the width/offset of these wheels but the fronts are pretty much flush with my fenders on front

and flush on the rear too, they will fit stock guards on the rear for a 180sx.

My front fenders are fiberglass and not sure if they are 30mm wider than stock but it should fit fine with stock fenders.

The rims weight are just over 7KG each. Here is some info on it.

http://www.auto.cons...-R_reviews.html

Comes with Tyres which are roadworthy (the front tyres 215/45/17) and rear is Kumho 235/45/17 (Rear tread is pretty new)

Must be in Victoria for Pickup only as it is trade/swaps.

IMAGES: http://nissansilvia....howtopic=433414

Depending on the Wheels for Swap - cash my way but not much.... make some offers smile.gif

Call 0431308544 or PM Me

Thanks Michael

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Yea that’s why I said ima test them with multimeter and see the reads.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      Only at idle. Isn’t a problem when rev it seems.
    • Murray_Calavera
      RB25DE NEO with Haltech ECU

      By Murray_Calavera · Posted

      @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...