Jump to content
SAU Community

Recommended Posts

so the other day i was driving for a good hour and a half or two and she was running strong all night, then i let her rev out in 2nd gear and after that i felt a power drop, like it had dropped cylinder or something, i thought maybe a dead spark plug?? any ideas?? sorry im only a newbie to these cars so i wouldnt no where to start looking.

the only mods done to it if that helps.. are:

arias forged pistons,

fast flowed turbo,

GTR fuel pump

upgraded ignition pack system (the red 1s...)

FMIC

apexi boost controller

cheers corey

Link to comment
https://www.sau.com.au/forums/topic/317597-power-drop-in-rb25det/
Share on other sites

2 things I can think of are:

heat soak from the engine bay that warms the intake pipes...when they get warm/hot feels much less responsive and it does loose some power..

but obviously the next day should be back to normal...

or the option I think is more likely: slightly popped cooler pipe, revving right out= full boost = highest pressure you've set and the most likely time a cooler pipe would pop off... but sometimes they don't completely pop off... so go around, check all the silicon joins and make sure theres no leaks..

gl, Adam

2 things I can think of are:

heat soak from the engine bay that warms the intake pipes...when they get warm/hot feels much less responsive and it does loose some power..

but obviously the next day should be back to normal...

or the option I think is more likely: slightly popped cooler pipe, revving right out= full boost = highest pressure you've set and the most likely time a cooler pipe would pop off... but sometimes they don't completely pop off... so go around, check all the silicon joins and make sure theres no leaks..

gl, Adam

awsome cheers ill have a look, that could deffenatly be it, as it was kinda sudden. thanks :D

awsome cheers ill have a look, that could deffenatly be it, as it was kinda sudden. thanks :happy:

your welcome.

you may need to double double check because you obviously can't hear it with the motor on... if your pretty sure that was it theres a few ways to check:

1. a little soapy water on silicon joins

2. or, theres kits you can buy or make up involving a compressor and what it essentially does is you put a cap on at the end of the intercooler piping, ie at throttle body or begginning of turbo outlet or between what ever part you think may be leaking and have a compressor blow into it with your motor off so it is quiet and you will definetly be able to hear the hissing if theres a leak...

you can also make this up yourself, if you youtube mighty car mods theres an episode where they make one.... couldnt find it, but if you look for more then 10 seconds you should find it..

your welcome.

you may need to double double check because you obviously can't hear it with the motor on... if your pretty sure that was it theres a few ways to check:

1. a little soapy water on silicon joins

2. or, theres kits you can buy or make up involving a compressor and what it essentially does is you put a cap on at the end of the intercooler piping, ie at throttle body or begginning of turbo outlet or between what ever part you think may be leaking and have a compressor blow into it with your motor off so it is quiet and you will definetly be able to hear the hissing if theres a leak...

you can also make this up yourself, if you youtube mighty car mods theres an episode where they make one.... couldnt find it, but if you look for more then 10 seconds you should find it..

cheers guys might try the soapy water trick as i dont have a compressor.. :happy:

Edited by ScreamerNewbie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...