Jump to content
SAU Community

Recommended Posts

so the other day i was driving for a good hour and a half or two and she was running strong all night, then i let her rev out in 2nd gear and after that i felt a power drop, like it had dropped cylinder or something, i thought maybe a dead spark plug?? any ideas?? sorry im only a newbie to these cars so i wouldnt no where to start looking.

the only mods done to it if that helps.. are:

arias forged pistons,

fast flowed turbo,

GTR fuel pump

upgraded ignition pack system (the red 1s...)

FMIC

apexi boost controller

cheers corey

Link to comment
https://www.sau.com.au/forums/topic/317597-power-drop-in-rb25det/
Share on other sites

2 things I can think of are:

heat soak from the engine bay that warms the intake pipes...when they get warm/hot feels much less responsive and it does loose some power..

but obviously the next day should be back to normal...

or the option I think is more likely: slightly popped cooler pipe, revving right out= full boost = highest pressure you've set and the most likely time a cooler pipe would pop off... but sometimes they don't completely pop off... so go around, check all the silicon joins and make sure theres no leaks..

gl, Adam

2 things I can think of are:

heat soak from the engine bay that warms the intake pipes...when they get warm/hot feels much less responsive and it does loose some power..

but obviously the next day should be back to normal...

or the option I think is more likely: slightly popped cooler pipe, revving right out= full boost = highest pressure you've set and the most likely time a cooler pipe would pop off... but sometimes they don't completely pop off... so go around, check all the silicon joins and make sure theres no leaks..

gl, Adam

awsome cheers ill have a look, that could deffenatly be it, as it was kinda sudden. thanks :D

awsome cheers ill have a look, that could deffenatly be it, as it was kinda sudden. thanks :happy:

your welcome.

you may need to double double check because you obviously can't hear it with the motor on... if your pretty sure that was it theres a few ways to check:

1. a little soapy water on silicon joins

2. or, theres kits you can buy or make up involving a compressor and what it essentially does is you put a cap on at the end of the intercooler piping, ie at throttle body or begginning of turbo outlet or between what ever part you think may be leaking and have a compressor blow into it with your motor off so it is quiet and you will definetly be able to hear the hissing if theres a leak...

you can also make this up yourself, if you youtube mighty car mods theres an episode where they make one.... couldnt find it, but if you look for more then 10 seconds you should find it..

your welcome.

you may need to double double check because you obviously can't hear it with the motor on... if your pretty sure that was it theres a few ways to check:

1. a little soapy water on silicon joins

2. or, theres kits you can buy or make up involving a compressor and what it essentially does is you put a cap on at the end of the intercooler piping, ie at throttle body or begginning of turbo outlet or between what ever part you think may be leaking and have a compressor blow into it with your motor off so it is quiet and you will definetly be able to hear the hissing if theres a leak...

you can also make this up yourself, if you youtube mighty car mods theres an episode where they make one.... couldnt find it, but if you look for more then 10 seconds you should find it..

cheers guys might try the soapy water trick as i dont have a compressor.. :happy:

Edited by ScreamerNewbie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
×
×
  • Create New...