Jump to content
SAU Community

Recommended Posts

Am i the only one that finds this funny?

Surfing SAU whilst tuning!

doing XR6 Turbos.... it takes between 5-7mins for each write. (make a change press enter then .....wait 5-7mins) seriously need someone to release decent LIVE tuning for these fkrs, its no wonder latley that i see the same map loaded in each car... someone locally is obviously too lazy to do it properly...... and they are making a fortune from it as its hardly viable to do it properly like i do.

i need something to stop me going crazy whist waiting hence inter-webs in the background :(.

Any reason why only 17 psi Trent. I know when I ran 15 psi through my 3071 on an SR it was fairly lame......when upped to 22 psi it was another story :rofl:

both cars were @ 90% inj duty...... damn killjoy for sure :P

both like to be around 20-22psi like you say, but these are the only two i have which are apples to apples, i have a few 22psi runs on the T67 (another car) but the GT3071is not complete.

Cars are off getting injectors so when they return i will post em up but i reckon months not days... :P

yeah you can see the L2's unhappy, the 8cm rear is just too small for the 2.5l. To make 300 its running 25psi .... a quick check of the exhaust manifold pressure would tell the story....

runs @ 17psi and i have picked the best average of both. The T67 is a bit wavy but has since been sorted.

just looking over that trent, goin by the colour of the lines... the 3071 which makes less power has a much fattter torque band? or.. are the colours switched around and i'm reading it wrong

hey toffy, I'm not so much a technical guy but when my car was setup i asked for a responsive setup without losing too much top end. Thought i'd share what i have. I was recommended into going with high flowing the stock r34 turbo and getting a garret gt30 core installed. I don't have the full turbo info but can get this info and others if interested. Here is my dyno chart.

post-50843-1272848801_thumb.jpg

hey toffy, I'm not so much a technical guy but when my car was setup i asked for a responsive setup without losing too much top end. Thought i'd share what i have. I was recommended into going with high flowing the stock r34 turbo and getting a garret gt30 core installed. I don't have the full turbo info but can get this info and others if interested. Here is my dyno chart.

post-50843-1272848801_thumb.jpg

3rd gear?

then its useless to use as a comparison unfortunately.

so i'll assume i read that sheet wrong than and the lesser power figure in yellow didnt go with the higher torque figure in yellow on the dyno sheet you posted...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...