Jump to content
SAU Community

Recommended Posts

Am i the only one that finds this funny?

Surfing SAU whilst tuning!

doing XR6 Turbos.... it takes between 5-7mins for each write. (make a change press enter then .....wait 5-7mins) seriously need someone to release decent LIVE tuning for these fkrs, its no wonder latley that i see the same map loaded in each car... someone locally is obviously too lazy to do it properly...... and they are making a fortune from it as its hardly viable to do it properly like i do.

i need something to stop me going crazy whist waiting hence inter-webs in the background :(.

Any reason why only 17 psi Trent. I know when I ran 15 psi through my 3071 on an SR it was fairly lame......when upped to 22 psi it was another story :rofl:

both cars were @ 90% inj duty...... damn killjoy for sure :P

both like to be around 20-22psi like you say, but these are the only two i have which are apples to apples, i have a few 22psi runs on the T67 (another car) but the GT3071is not complete.

Cars are off getting injectors so when they return i will post em up but i reckon months not days... :P

yeah you can see the L2's unhappy, the 8cm rear is just too small for the 2.5l. To make 300 its running 25psi .... a quick check of the exhaust manifold pressure would tell the story....

runs @ 17psi and i have picked the best average of both. The T67 is a bit wavy but has since been sorted.

just looking over that trent, goin by the colour of the lines... the 3071 which makes less power has a much fattter torque band? or.. are the colours switched around and i'm reading it wrong

hey toffy, I'm not so much a technical guy but when my car was setup i asked for a responsive setup without losing too much top end. Thought i'd share what i have. I was recommended into going with high flowing the stock r34 turbo and getting a garret gt30 core installed. I don't have the full turbo info but can get this info and others if interested. Here is my dyno chart.

post-50843-1272848801_thumb.jpg

hey toffy, I'm not so much a technical guy but when my car was setup i asked for a responsive setup without losing too much top end. Thought i'd share what i have. I was recommended into going with high flowing the stock r34 turbo and getting a garret gt30 core installed. I don't have the full turbo info but can get this info and others if interested. Here is my dyno chart.

post-50843-1272848801_thumb.jpg

3rd gear?

then its useless to use as a comparison unfortunately.

so i'll assume i read that sheet wrong than and the lesser power figure in yellow didnt go with the higher torque figure in yellow on the dyno sheet you posted...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
×
×
  • Create New...