Jump to content
SAU Community

Vvt On My Current Neo Motor Has Been Disconnected... Why?

fubar

By fubar,
in Engines & Forced Induction

 Share

Recommended Posts

fubar Enthusiast

fubar

Posted
Posted

Hey guys

Change of plan can't get pistons made up for my car for 8 weeks so not rebuilding atm, im just going to buy a second had neo motor and smash it in for the meen time.

My original motor (rb25det neo) has had the vvt disconnected, ant reason for this? and what can i do with the other motor being installed in regards to the vvt swap everthing off the old motor?

Apparently in japan it had gtr cams put in but yet to conform it, the cams are out but need to measure the lift... What is the standard lift?

Also the injectors are blue and top mount. the only numbers i could get was EBJE100 any idea what they are? couldn't find anything on the net.

Cheers

fubar Enthusiast

fubar

Posted
  • Author
Posted

I just measured my cams and i have

Inlet 86mm

exhaust 82mm

That means they are gtr cams

Standard neo are

inlet 84mm

exhaust 87mm

Just wondering if i replace the original cams in the second hand motor with the gtr cams and disconnect the vct is that all i have to do to make it work?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
    • GTSBoy
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By GTSBoy · Posted

      Plan B? Get someone to machine up a metal bush/collar/whatever it needs to be to replace the rubber? I haven't had a close look at that part recently to have a proper feel for whether that's possible. But it might be easy.
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      I do not want to install a short shifter and the only other stock throw shifter I have seen is the Nismo "Rigid shifter" for $290 So plan A is to fill it with sikaflex to stiffen it up and hope for the best
×
×
  • Create New...