Jump to content
SAU Community

Qld Licences To Go All James Bond

Isola

By Isola,
in Queensland

 Share

Recommended Posts

Isola Grand Master

Isola

Posted
Posted (edited)

Reposting from the 300ZX forum:

QLD Licence changes

copypasta for those too lazy to click

A NEW licensing regime has cemented Queensland's position as one of the most costly places in the country to own a car.

Following massive increases in registration, the demise of the fuel subsidy and the looming impost of higher tolls, the Bligh Government on Wednesday unveiled big increases in licensing costs.

The spike will fund the introduction of the long-promised digital driver's licence, which has blown out from a potentially cost-neutral exercise to a $110 million system.

A five-year licence will jump in cost from the current $73.30 to $96.05 next year, and rise to $152.50 by 2014-15, putting Queensland in line with the highest-charging states.

The cost of other licence and authority cards will also skyrocket, including learner's permits, boat licences and the adult proof of age card, which will replace the 18+ card.

The new regime will add to registration rises of up to 22 per cent last year, a statewide 9.2 per cent increase in fuel prices after the subsidy was scrapped and big toll hikes from July 1.

While the Bligh Government defended the new cards and their ability to tackle fraud, the Opposition blasted the price hike.

State Transport Minister Rachel Nolan yesterday insisted the introduction of the new secure licence system was essential to fight fraud. "I don't think that anyone really believes that the old laminated licence is really an appropriate primary form of ID in 2010 and into the future," she said.

RACQ external affairs manager Gary Fites said the additional costs needed explaining but drivers would welcome the additional security.

"People are very security conscious and will see the benefit of that," Mr Fites said.

However, Opposition transport spokeswoman Fiona Simpson said motorists were again being forced to be the Bligh Government's cash cow.

"It is time for Anna Bligh and Labor to get their sticky fingers out of motorists' pockets," Ms Simpson said.

The new licence delivers on promised security improvements with biometric imaging replacing polaroid photos as well as holograms and watermarks to make duplicating the cards much more difficult.

However, the hi-tech convenience mooted to come with the card – such as paying for parking tickets – has failed to materialise with its computer chip little more than an idle accessory. Address details will still be printed on the card.

Ms Nolan conceded the card's computer chip was currently under used but available for future purposes. "We have future-proofed the card and provided a technological capacity," she said.

Police will be able to access the digital images of drivers for traffic offences and emergencies but must apply to a justice of the peace if the photo is required for other purposes.

Edited by Isola
Link to comment
https://www.sau.com.au/forums/topic/320495-qld-licences-to-go-all-james-bond/
Share on other sites
HtwCHACtkh Community Regular

HtwCHACtkh

Posted
Posted

I understand intelligent I.D to tackle fraud, you use your drivers licence to open bank accounts. I don't get the major hike in price here...

GoCards are programmable/have data on them and cost like $5 or something. What's the extra ~$50 all about?

Smity42 Grand Master

Smity42

Posted
Posted
I understand intelligent I.D to tackle fraud, you use your drivers licence to open bank accounts. I don't get the major hike in price here...

GoCards are programmable/have data on them and cost like $5 or something. What's the extra ~$50 all about?

Cap'n bligh trying to recover all the funds she squandered.

I got my rego renewal notice yesterday and it had an add for Hyundai packaged with it. I wonder how much income that's bringing her?

stimps Collaborator

stimps

Posted
Posted
Protest letter written and emailled.

http://www.thepremier.qld.gov.au/tools/contactform.aspx

I advise everyone to send their angry comments (dont swear) to this form, let anna know how hated she is.

It will only take someone to start revolution i think, someone to start a major show of unhappiness in the government right now, just to get the ball rolling, and they would be running scared.

They would never dream of governing in france like they do here, why are we so apathetic!??? they get away with this here coz we LET THEM.

whos going to lead a revolution and shut these idiots down?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...