Jump to content
SAU Community

Engine Rebuild - Court Case

Sinista32

By Sinista32,
in New South Wales

 Share

Recommended Posts

Sinista32 Grand Master

Sinista32

Posted
Posted

There was a thread yesterday about an SAU memeber who was taking a workshop to court over an engine rebuild gone wrong in the Newcastle area "Hill". Today its MIA. What happend to this thread Mods? :P several pages wiped. Was this censored or removed at the request of the initiator?

Link to comment
https://www.sau.com.au/forums/topic/320514-engine-rebuild-court-case/
Share on other sites
SECURITY Grand Master

SECURITY

Posted
Posted

hey mate, it was my thread.

out of interest of the club it was taken down so not to implicate anyone as there were too many references to the workshop's possible name. the workshop and/or its representative contacted Christian (PranK) to make sure it was all in order - its much easier to take it down than to have to worry about what is said in the thread, it was getting a little off topic anyway.

it doesn't bother me, i will just start another thread with progress of my claim - anyone wanting further details can email me on joe.rulz at hotmail.com to keep it away from the forums.

FrangaR33 Mentor

FrangaR33

Posted
Posted
hey mate, it was my thread.

out of interest of the club it was taken down so not to implicate anyone as there were too many references to the workshop's possible name. the workshop and/or its representative contacted Christian (PranK) to make sure it was all in order - its much easier to take it down than to have to worry about what is said in the thread, it was getting a little off topic anyway.

it doesn't bother me, i will just start another thread with progress of my claim - anyone wanting further details can email me on joe.rulz at hotmail.com to keep it away from the forums.

I'm eager to find out how you go with your case. I look forward to the new thread to see how it goes. Good Luck mate.

Sinista32 Grand Master

Sinista32

Posted
  • Author
Posted

When all is said and done I'd appreciate a PM.

I've been through a divorce and I have been through a rebuild gone bad. Financially and emotionally they're both costly.

There's no winner and do not expect justice.

I hope you were able to read my last post, prior to the thread being removed.

Advice I gave may tip the scales in your favour.

S!N

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
    • GTSBoy
      Strange issue RB25DET wont start

      By GTSBoy · Posted

      Yeah, I would have said the same. It makes me suggest that there are other things wrong, such that the ECU is totally unhappy with the broken sensor. The only other thought here is that maybe it is shorted, which might cause a different issue to the typical "disconnected" sensor.
×
×
  • Create New...