Jump to content
SAU Community

Recommended Posts

hey guys

ive got my hands on a pair of cheap 2540s and i was just wondering how the 2540s compares to the 2530s i know its bigger but how much laggier is it? how much more power will it make? also whats the difference between the 2540s and gtrs which one is bigger?

thanks

Link to comment
https://www.sau.com.au/forums/topic/321003-hks-gt2540-vs-hks-gt2530-on-a-rb26/
Share on other sites

2540s are a terrible turbo. Nobody wants them. It's been covered in a few threads now.

They make pretty much the same peak power as 2530's, but with more lag and hence they always sell cheap.

Still bemuses me why HKS even released them when the 2835 was the better choice (as the time) if you wanted bigger than 2530's

They are not as big as GT-RS's.

i can see why HKS did it but yeah the results weren't that great

you got a bit more power, but you paid for it with the penalty of more lag

as the others have covered off in other threads this where this is a bit of a power gap from bolt on replacement turbochargers

i guess HKS tried to fill that gap a bit but it came out with a more laggier penalty vs gains

un related

id like to an external gate GTR TWIN 2835 (1 of them) on a single rb25 setup and see how does that perform

yes i know wrong flange, wont mate up, but i reckon this could be a real killer

Actually the compressor wheels in the 2540's were larger than GTRS's use . 2540s used a 76mm T04E compressor wheel from memory in 46 trim where GTRS's have a 71.1mm GT wheel in 52 trim .

GT2835's also use 71.1mm GT comp wheels so again smaller than 2540's T04E wheels .

Don't know why HKS used that 2540/T04E comp , would have been better off using twin 2535's .

A .

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...