Jump to content
SAU Community

Recommended Posts

you had a dream last night didn't ya sid? hangin for a line i see :D

correct me if im wrong guys but as far as registration goes, i beleive it has to be NSW plates unless you fully unrego the vehicle and somehow truck it down to Melbourne get the RWC and register it under VIC?

Well this may or may not be helpful information. But my last car was SOLD interstate to a guy from Adelaide. Now what we did was a risk to him if he decided to drive stupidly.

I cancelled my registration on my car but didnt hand in the plates (basically if you cancel your registration you get a refund on your remaining rego. But you only get the refund when you hand your plates back. However if you dont hand your plates back for a month or more from when you cancel your rego you still get the full allotted refund)

So I cancelled my rego - let him drive back to Adelaide with my cancelled plates on so he could do everything he needed without trucks etc - then he sent me the plates back in the mail. It all worked fine for everyone... but it only happened cause I was a nice bloke who did the guy a favour, and because the guy driving with cancelled plates didnt drive in a manner to draw attention to himself.

Thats the easiest way if both parties are good.

I was going to buy a skyline from NSW so i investigated this a while back. I was going to fly up, buy the car, get proof of purchase, drive down to vic.

Then hand the NSW plates in to Vicroads, they give the registed owner the refund (the old owner), then you have to get a Vic RWC and get new rego. So its still registered to the old owner when you drive it interstate, but as long as you have proof of purchase you can hand the plates in yourself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...