Jump to content
SAU Community

Recommended Posts

recently i put an r34 gt-t turbo in my r32gts-t

anyway since then i've had this odd sounds, it kind of sounds like it could be an exhaust leak or something rattling even

it loudest from under the passenger side door, but you can hear it a bit in the engine bay

at first i thought it was an exhaust leak from the joint in the exhaust between the front pipe and cat

i can confidently say that isn't the problem after replacing the gasket and bolts and what not

at first i instantly thought it was an exhaust leak from a turbo gasket but i have been over these and they certainly do no appear to be leaking all the nuts and bolts are done up tight the head to exhaust mani gasket has also been replaced a bit less than a year ago. (all gaskets were replaced with legit nissan items)

this sound is driving me insane, i'm now left thinking has my cat collapsed? could shit be rattling around inside of it because it sounds like it when i lay under the car

the cat isn't anything special it's been welded onto the exhaust on the outlet side of it because the exhaust is 3.5" and the front pipe is 3" the cat is either stock or something but it's 3"

is it even possible to have something rattling around in a cat? i'll admit i don't really know what goes into one

Thanks

Dan

ps. as far as losing power that goes with a cat dying etc, it does come on boost fairly late i realise it's a bigger turbo but it's dead set not full boosting until around 4500rpm for 0.8bar

Link to comment
https://www.sau.com.au/forums/topic/323658-collapsed-cat/
Share on other sites

the r34 turbo on an rb20 will boost at pretty high rpms. that's just the joys of owning the lag monster that is the rb20. 4500rpm might be a touch high though.

if the cat was collapsed then it may rattle, but you would also find that boost at high rpm would start to drop off.

also i would recheck all the manifold studs. make sure none are broken. other than that the only other real possibility is that the turbo is stuffed.

Link to comment
https://www.sau.com.au/forums/topic/323658-collapsed-cat/#findComment-5278181
Share on other sites

i had all the studs replaced and helicoiled when i destroyed the thread for a couple of them inside the head

so they are all new

yeah i'm aware it will have some lag, that 4500rpm was a figure i had from just after i put the turbo on.

tbh i think it's even later now after i did a track day a few weeks ago and the sound that i think is the cat has kinda gotten a bit worse too

Link to comment
https://www.sau.com.au/forums/topic/323658-collapsed-cat/#findComment-5278679
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...