Jump to content
SAU Community

Recommended Posts

hello

My alternator is making a whistling noise, it just started in the last week. The noise gets louder if i have more accessories switched on eg. lights, fan, rear demister.

Can the brushes in these alternators be replaced?

Could it just be a loose drive belt on the alternator?

should i just get a new one? if so how much do they cost?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/324289-r33-alternator/
Share on other sites

hello

My alternator is making a whistling noise, it just started in the last week. The noise gets louder if i have more accessories switched on eg. lights, fan, rear demister.

Can the brushes in these alternators be replaced?

Could it just be a loose drive belt on the alternator?

should i just get a new one? if so how much do they cost?

Cheers

The whistling could be the belt slipping. Undo the lock-block bolt and turn the tensioner bolt a couple of turns. See if that helps.

Maybe also the bearings are done with life. They can be replaced. Brushes shouldn't make it whistle and yes they can be replaced.

I rebuild them for fun so heres some info

http://www4.wave.co.nz/~lakewood/Skyline/Alt.htm

Yours can be serviced.

Nigel

Link to comment
https://www.sau.com.au/forums/topic/324289-r33-alternator/#findComment-5285254
Share on other sites

The whistling could be the belt slipping. Undo the lock-block bolt and turn the tensioner bolt a couple of turns. See if that helps.

Maybe also the bearings are done with life. They can be replaced. Brushes shouldn't make it whistle and yes they can be replaced.

I rebuild them for fun so heres some info

http://www4.wave.co.nz/~lakewood/Skyline/Alt.htm

Yours can be serviced.

Nigel

I tightened the belt and it appears to have helped a bit. Still sounds a bit funny tho i rekin i might give servicing it a shot. will i need a press to change the bearings?

I had a look at the alternator it is a Mitsibushi 23100 70T17 90A do you know the part numbers for bearings and brushes?

Thanks

Edited by ForcedInduction
Link to comment
https://www.sau.com.au/forums/topic/324289-r33-alternator/#findComment-5285649
Share on other sites

I tightened the belt and it appears to have helped a bit. Still sounds a bit funny tho i rekin i might give servicing it a shot. will i need a press to change the bearings?

I had a look at the alternator it is a Mitsibushi 23100 70T17 90A do you know the part numbers for bearings and brushes?

Thanks

Ah sorry not had the 23100-70T17 apart. Mostly I rebuild the Hitachi units. The small rear bearing is the most difficult to get off. I grind the outer bearing ring to allow all the balls to drop out and the outer ring falls off then just use a linish belt to grind away the inner ball race until it loosens and slides off. There is not much room to get a puller around it. By all accounts the front bearing is a slide fit both on the shaft and in the end cover.

Just note the bearing numbers beofre you remove them, any bearing dealer handles them, not just sparkies.

Nigel

Link to comment
https://www.sau.com.au/forums/topic/324289-r33-alternator/#findComment-5286217
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...