Jump to content
SAU Community

Recommended Posts

Sup, as described in heading,

Before I go to Nissan sourcing 'new' parts, figured someone's wrecking some of these random items. All for R32 GTR.

1x Headlight Switch Assembly. I may also take the whole fascia that surrounds the cluster.

1x Battery Cover. "If" they help hold the battery a little more still. I have the clamp but no battery cover, so only sheer clamp force will hold the battery firm.

10x Floor plugs. (The ones you will find holding your boot trim to the car)

The parts that sit in the door trims to hold the 4x6" speaker in place. Namely the speaker mounts, anything that stacks on top of them, and the "active speaker" stock speaker covers.

1x Spare wheel (can come in the form of a radial with no tyre, mainly after the rim)

1x Spare wheel cover.

1x Drivers seat adjusting lever. (The plastic handle)

1x Centre console fascia. Gloss black. (The plastic surrounding the radio/climate/centre gauges) - Ashtray and lighter optional.

1x ABS Unit. (The solonoid block near the turbos)

PM any costs + delivery to 2259.

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/327597-lf-r32-gtr-parts/
Share on other sites

Sup, as described in heading,

Before I go to Nissan sourcing 'new' parts, figured someone's wrecking some of these random items. All for R32 GTR.

1x Headlight Switch Assembly. I may also take the whole fascia that surrounds the cluster.

1x Battery Cover. "If" they help hold the battery a little more still. I have the clamp but no battery cover, so only sheer clamp force will hold the battery firm.

10x Floor plugs. (The ones you will find holding your boot trim to the car)

The parts that sit in the door trims to hold the 4x6" speaker in place. Namely the speaker mounts, anything that stacks on top of them, and the "active speaker" stock speaker covers.

1x Spare wheel (can come in the form of a radial with no tyre, mainly after the rim)

1x Spare wheel cover.

1x Drivers seat adjusting lever. (The plastic handle)

1x Centre console fascia. Gloss black. (The plastic surrounding the radio/climate/centre gauges) - Ashtray and lighter optional.

1x ABS Unit. (The solonoid block near the turbos)

PM any costs + delivery to 2259.

Thanks in advance.

Hi mate give Erwin a call i know he Wrecking complete R32 GTR so im sure he got all the parts you need.

0410069096 or sms him.

pretty sure i have one, will get back to ya

** EDIT: is this what you are after?

DSC00334.jpg

I haven't taken it out yet so I dont know what it looks like underneath, but that looks to be the part yeah. Does it work properly? Mine turns only one light on, the maybe the other if it wants, taked 100 goes to get both lights on. I heard the lights run off the switch without relays, so I'll be wiring up a set of relays this weekend to save the next switch a bit.

How much if it's good mate?

Hi mate give Erwin a call i know he Wrecking complete R32 GTR so im sure he got all the parts you need.

0410069096 or sms him.

Interesting you say that, I just bought a rear seat off him and thought he rorted me! Lol but it's ok it came through today, I was worried cause of another issue we had bout 12 months ago when I received some faulty stuff, which he since replaced free of charge. I'll give him a call anyways, thanks!

I have the ABS Unit here ready to go

$150 plus delivery from perth

PM me if you want or msg me on 0422 648 745

Thanks Daniel

Hey Daniel,

The prob with mine is it's leaking, spoke to a few people and they say it's rare for them to leak? So I must ask the question for the record, does yours leak? :ninja:

Thanks all who are helping me out.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...