Jump to content
SAU Community

Recommended Posts

Make/Model:

R31 S3 Skyline

Year:

1989

Kilometers:

253 xxx on shell

Transmission type:

RB25det manual

Engine:

RB25det

Colour:

White

Modifications:

RB25det

Serviced every 5k

New water pump, t-belt ect

kkr480 turbo

External gate an screamer

High mount mani

fmic an 3" piping

turbo smart vport bov

top half plenum (garage 7)

sard 550cc side feed injectors

sard fuel pressure reg

s13 hsd coil overs

17*9 driftex all round

r33 front brakes

s14 front hubs

4:11 mini spool diff (built by boss differentials)

3" mandrel bent over diff turbo back exhaust with xforce muffler)

race seat on r31 rails, non fixed back

custom tail shaft

xtreme drift clutch

rb25 box

walbro fuel pump

adj caster arms

battery in boot

microtech ltx-12

285kw on 16psi, tuned up to 20psi

has only done 6500km since build. all components bough new while building

Registered:

yes

Accident History:

none

Asking Price:

$12000 ono or swaps for something of interest..

Contact:

0447022133 or pm me

post-68356-1278414717_thumb.jpg

post-68356-1278414736_thumb.jpg

post-68356-1278414744_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/327839-eoi-r31-s3-rb25det/
Share on other sites

Did the same thing but in a hr.. I'd swap u the steg but you would have to come up with a bit of cash. ITs not worth that much to me because I could build it quick.

Edited by slydin_s13
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...