Jump to content
SAU Community

Recommended Posts

Hi all

wanting to know if any1 has any idea Wat is up with my goddy , ???

1st of all i recently had problems with my turbos e.g white smoke pouring out exhaust and oil all threw my inter cooler pipes, i went to c.n.j motor sport up in Underwood and they said the turbos r fine but i have since found out that they are not fine and i have done a oil seal ..... anyway i have just gathered up enuf money to send it to Godzilla motor sport as i have heard good things about them can any1 confirm that ?? its going in for new turbos and tune etc ..... now here's the big but :) i started the car up which was running fine even tho turbos r no good and it seems to be now dropping a cylinder or 2 does any1 have any ideas as to y its running like that now when it wasn't even after the turbos went ages ago????

any help would be great thanks

Link to comment
https://www.sau.com.au/forums/topic/328000-running-like-shit/
Share on other sites

You said you had oil in your intercooler pipes, my guess would be that the oil in the intake has fouled up your spark plugs. possible quick fix is to pull ur plugs out and give them a clean

Thanks heaps for that might thought that might be the problem I wil get them to do it at shop..do u know anything bout Godzilla Motorsport??

Thanks heaps for that might thought that might be the problem I wil get them to do it at shop..do u know anything bout Godzilla Motorsport??

Ive never been there but i have heard some very good things about them , and seen some very tough engines come out of there

sweet as hopefully they will be building one more :yes: thanks for ur help

Hey me again

found out today its my bottom end that needs rebuilding so wanting some advice as to wat parts to throw back in as i want a good strong engine thats good for 650hp-700hp, just trying to suss out how much parts for bottom end would roughley be before i go buying up .....

any help please ??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45掳 silicone hose from the TB, like the alloy pipe that is currently there, to another 45掳 silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
  • Create New...