Jump to content
SAU Community

Recommended Posts

Yes. they were the one's that were good enough to record the car's current PB of 9.38 @ 152.25mph.

I have photo's, but they are over the 100kb limit here.

If you want them, give me your e-mail address and I will forward them on.

Just going for a different setup...and I'm tired of dealing with speedshops who want your money, but don't earn it.

Yes I will separate...if you can find someone else to buy the other one.

More or less buy both and sell one or share the purchase with another.

I would have thrown one on the REX if I was going to keep it. But I've just detuned it to sell....no more coilovers, mags, APS kit etc. back to almost stock.

This is the time to meet me on the street, when it's only half a weapon....it's all good fun though....there's a time and place for everything.

Have fun, live to enjoy life.

I have a td06-20g on my rb25det and its the ducks nuts. Been for a drive in my mates gt30 equiped rb25det and it's fast too but my car pulls harder and stronger and keeps pulling to the rev limiter, 7500rpm, we are considering taking it up another 500-1000rpm :D

do you have manifolds and dumps to suit the kit? if so im intrested on the whole deal. i have a near new hks T51R kit for a gtr if you want to do a trade deal or something down the line. its made over 720hp at all four wheels out off it on 28psi so im looking for some more power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...