Jump to content
SAU Community

Recommended Posts

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Still to go. Price drop

Bonnet $220

lhs front gaurd $100

rhs front gaurd $100

rhs front headlight $100

gaurd orange indicators $20 pair

dash missing two small vents on top $100

center consol $50

heater/aircon control $40

heater $100

rear seats $130

entire floor carpet $100

roof lining $50

center roof light $20

map lights $20

holy shit handles on roof $10

lhs a pillar $20

speedo cluster $100

glovebox $40

rear seatbelts $20

rhs sun visor $20

rear lhs tail light $100

passengers door$150 with all electrics

door linings and electrics can be separated along with mirrors

side skirts (one cracked) $50 pair

windows (remove yourself or get removed properly) $$$

3"catback exhaust with emptied cat and rear cannon $350

interior lining $80

parcel shelf $50

boot lining $50

boot seal $25

bonnet latch $35

horn $15

fuel tank $100

rear skyline strip between lights $60

scuff panels inside doors $25 pair

fuel cap covering panel $20

windscreen wiper stalk $15

indicator stalk $15

steering column $40

front calipers $250 pair

rear rotors and calipers $200

front 5stud hubs $100 pair

rear 5stud hubs $100 pair

standard diff $200

front suspension $100

  • 4 weeks later...
  • 2 weeks later...

Bump

all this needs to go- all offers considered-just taking up room need it gone,

complete rear subframe has been pulled out too.

Bonnet and rear seat no longer available-

rear calipers are stil available-

0419837474.

  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...

do you still have the front bar? i need the indicator/driving light section for a series 1, same as 1.5, need those front panel lights!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...