Jump to content
SAU Community

Recommended Posts

hey all, im new to this site & skylines

i recently bought a R33 GTS4 paid about 3500 for it.

i was just wondering is there a way to disable the attesa system?

and then simply just plug it in again?

or is this only the R32's?

any feedback would be greatly appreciated:)

thanks

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/
Share on other sites

you cannot just pull out a fuse like in the 32's. this is because their system was electrical and the 33's are hydrological.

You can drain the resovior in the boot but the safest thing to do is take out the front drive shaft.

BTW, how did you manage a 33 gts4 for 3.5k? is it damaged?

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5356095
Share on other sites

The caniser in the boot runs down to the actuator on the O\S\R of the car, it pumps fluids to the transfer case and when the slip light is activated it then runs too the rear diff and is pumped around there aswell, then back too the canister. It does this because it is a high pressured pump that activates clutch packs in the transfer case, this is how the attesa system works. Do not take the fluid out of the clutch packs with be distroid and you will have to spend a lot of money and all the parts with be EX jap.

The fluid is a ATF fluid, at nissan we sell nissan Matic D which is what they used stock.

You can take the front propeller shaft out but thats it.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357381
Share on other sites

how would i pull out the shafts? just pull them out

your only taking out the front shaft.

It is located under the car more towards the drivers side next to the gear box area.

there are four bolts that attach it to the car, they are in pricks of a position to get off...

the thing i do is, move one bolt at a time to the best position possible for you to reach by rolling the car, undo it and take it off, roll your car a little back or forward so the next bolt is in the same position and repeat.

when you get good at it, you can have it off in 10-15 mins if that....

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357421
Share on other sites

As said before.

You can only disconnect the 4wd system in the R32's electronically.

In the 33 and 34 you must remove the front drive shaft.

This is the shaft from your transferbox (the thing hanging off the drivers side of the gearbox) going up to the front diff.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5359314
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG is has not responded to my emails so far after purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
×
×
  • Create New...