Jump to content
SAU Community

Recommended Posts

After a few mths of deciding, i have opted to sell my r33 gtst. What i am looking for now is a STOCK R33 GTR around the 1996+ yr. Reason being i want to start from the ground up like whant i did with my current R33.

In the past i have seen a few private sale selling them for around $32-35k. Just wondering if any of you guys have seem them around that price sold privatly? Or know of any dealers who have them (willing to spend a little more). In the past i have noticed that Advance Auto Imports havehad soem quality cars sold. I wouldnt even bother with Auto JMart just totally dodge!

Im really looking for an immaculate GTR as my current gtst is very emaculate. I have seen some around for $37-40k but then come with ECU, hks cooler, 3.5inch zaust..

Thanks.

:)

Link to comment
https://www.sau.com.au/forums/topic/32980-gtr-sales-in-brisbane/
Share on other sites

I had a good look around Brisbane and there really wasn't much to look at. Well during the 6 months that I was looking around, especially in that price bracket. You definately will not find any in yards for that price they are all $40+K. In that price range make sure you really look the car over, as you are in accident repair area, unless you are lucky enough to find a good cheapie. This one is worth a look if you can get to it before he trades it in definately no accident damage here. It pretty much fits your criteria and I have driven this one myself, very nice.

http://www.skylinesaustralia.com/forums/sh...ead.php?t=24847

Might be worth sending supahiro27 a PM I think he has one (or two) for sale at the moment.

This one may also be worth a look although it doesn't really fit your requirements.

http://www.skylinesaustralia.com/forums/sh...6&highlight=GTR

thanks for the info jlnewton, sent the first guy a PM and email, hopefully he hasnt sold it yet.

I went to look at a 95 model lastnite (took along mu mecanic friend). The guy had it on the add for $37k and 96 model. When i got there noticed it was a 95 model. my mate then checked it all over, noticed that the front bumper had a crack, stock mags had gutter damage, head casket had a oil leak on the back of the engine ($150 to replace without labour), seats were not in good condition (very warn), and there the shaft bearing (i think thats what its called) in the gearbox was noisy. He said normally if the shaft bearing in the gearbox goes, means the gearbox could also go. Like if a throwout bearing in the clutch goes, the whole clutch is about to go also. Gear boxes go for around $3000+, so i offered him $33k for it. He rang back this morning sayin the lowest is $34k... I got a few more to look at, but at the moment that car is last on my list.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...