Jump to content
SAU Community

Recommended Posts

Selling my car as I've recently started a new job and I rarely use my car anymore. I did have a thread up for my car before, but being busy with work and personal issues did not continue with the sale of my car and I guess the thread disappeared.

Here are the cars specs:

- Black 1993 Series 1 GTS25

- 5 speed manual

- Chassis and engine has done 16X,XXX KM (Odometer was changed prior to me purchasing the car as the dials on the old cluster were not functioning)

- Rego until Feb 2011

- Full 2.5" exhaust throughout installed by Bankstown Muffler Fit

- New Century Battery installed

- Harmonic balancer and key crank replaced/repaired

- Lowered suspension

- 18" 2 piece rims

- Aftermarket alarm system and immobiliser

- Momo steering wheel

- Automatic Climate Control

- Paint is in average condition. Clear coat peeling on spoiler and driver side front guard.

Note:

- Hit and run has damaged the current front bar and reo. I do have a spare front bar for the buyer to use, however it is in a two tone grey colour and will need to be resprayed. Headlights and indicators haven't been touched and radiator support is straight.

- Dent on rear quarter panel (existing damage from previous owner)

- Driver side window does not work, will need a new regulator (roughly $100). Passenger side window works fine

- Central locking will not unlock the doors using the remote. Alarm however is still in perfect working order and immobiliser works 100%

Pictures:

th_6.jpg th_1-1.jpg th_2-1.jpg th_3.jpg th_4.jpg th_5.jpg th_7.jpg th_8.jpg

Price:

4.5k with rego ono

The car runs smoothly and hasn't missed a beat since the repairs and I have the receipts for most of the work done to the car. The exhaust has a nice deep rumble for an N/A car and doesn't attract too much attention.

Contact:

Via PM or call/sms 0431 737 515

Link to comment
https://www.sau.com.au/forums/topic/331105-r33-series-1-gts25/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I normally run with I think a 10mm, and definitely use the second handle you can add to a drill. They hurt when they bins up!   For the crush tube, once all subframe is clear, I'd try some stilsons and see if I can get it to start to twist.
    • Probably because they couldn't, because the use of the variable resistor to create a "signal" in the ECU is managed by the ECU's circuitry. The only way that VDO could do it would be if they made a "smart" sensor that directly created the 0-5V signal itself. And that takes us back to the beginning. Well, in that case, you could do the crude digital (ie, binary, on or off) input that I mentioned before, to at least put a marker on the trace. If you pressed the button only at a series of known integer temperatures, say every 2°C from the start of your range of interest up to whatever you can manage, and you know what temperature the first press was at, then you'd have the voltage marked for all of those temperatures. And you can have more than one shot at it too. You can set the car up to get the oil hot (bypass oil coolers, mask off the air flow to oil coolers, and/or the radiator, to get the whole engine a bit hotter, then give it a bit of curry to get some measurements up near the top of the range.   On the subject of the formula for the data you provided, I did something different to Matt's approach, and got a slightly different linear formula, being Temp = -22.45*V + 118.32. Just a curve fit from Excel using all the points, instead of just throwing it through 2 points. A little more accurate, but not drastically different. Rsquared is only 0.9955 though, which is good but not great. If you could use higher order polynomials in the thingo, then a quadratic fit gives an excellent Rsquared of 0.9994. Temp = 2.1059*V^2 - 34.13*V + 133.27. The funny thing is, though, that I'd probably trust the linear fit more for extrapolation beyond the provided data. The quadratic might get a bit squirrely. Hang on, I'll use the formulae to extend the plots.... It's really big so you can see all the lines. I might have to say that I think I really still prefer the quadratic fit. It looks like the linear fit overstates the temperature in the middle of the input range, and would pretty solidly understate what the likely shape of the real curve would say at both ends.
    • I got a hand held bisssel one and it's a piece of shit. Doesn't work for more than about 5 seconds. So much so that I nearly refuse to believe any wet dry vac actually works or has enough suction to clean the carpet of a car. I'm discouraged as all the good ones are $300+ for an unknown result. I saw MCM did a Ryobi video where they use this thing: https://www.ryobi.com.au/products/stick-vacuum-cleaners/18v-one-hptm-brushless-spot-cleaner-tool-only Anyone have any experience actually using a tool like this when not paid to showcase it?
    • That could very well be the thermistor, but the ECU only sees Volts. VDO don't seem to provide a 0-5 volt curve, only the resistance curve.... (or line).
    • Yes. Probably, given that there is only access from the bottom end of it, go with a drill bit. Don't start too small. 7 or 8mm is probably the right size. You want something that can make a big enough hole to do some damage, but not so bit that it clashes with the steel or binds up and breaks your wrist. A slow speed is probably a good idea too. Once the rubber is destroyed, you then have to get the crush tube off the stud, which will be the whole heat/oil/cutting exercise all over again, but this time with the need to strictly avoid damaging the stud (any further than the corrosion might already have done.
×
×
  • Create New...