Jump to content
SAU Community

Recommended Posts

Do after you changed the belt do the gears match up with the marks when the balancer is at 0?

It will still run as you will still get some compression but it won't run well. If they are overly bent or you have knocked the head off the valve that cylinder won't fire.

Edited by D_Stirls

Madaz. See stag section for full report, I think basicly what's happened... The belt came off, I aligned the can wheels, then moved the crank wheel around to it's mark. I used a breaker bar on the harmonic bolt... I think me forcing it round( thinking it was just compression lock up... May have bent valves, not knowing what I'd done I put it back together and started it, sounded real exhaust leakish... I should have left the belt on and span it witch I wasn't aware/ think of then!

D stirls, yep all lined up, but I made it line up by forcing it to, witch I think is when I 1st bent stuff...

Do after you changed the belt do the gears match up with the marks when the balancer is at 0?

It will still run as you will still get some compression but it won't run well. If they are overly bent or you have knocked the head off the valve that cylinder won't fire.

Yeah but how am I going to a compression test? I can't keep cranking it over. Or is it ok Ish if it's not firing...? What's new valves and sleeve going to cost?? And how much time to swap lol

Yeah you really shouldn't force things

Time for the had to come off then.

Do a compression test and that will tell you the story. And then if it's low, off with the head, new valves and guides.

If it's lined up now then you should be able to turn it over without doing anymore damage than what has already been done. Hopefully you don;t drop a valve in the process. But without a compression test you might pull the head off and there will be nothing wrong (unlikely though).

Ok will do. So just unplug cas n go each cyl. Is it likely 2 be more than 1 cyl u rekn,

And I'll have to do all 24 valves, and all sleaves go them, anything eles? Just go stokies again? Do 26 ones fit? Likely to have piston damage?

If it's lined up now then you should be able to turn it over without doing anymore damage than what has already been done. Hopefully you don;t drop a valve in the process. But without a compression test you might pull the head off and there will be nothing wrong (unlikely though).

Pull all the plugs as well. Take the fuel pump fuse out and unplug the injector loom.

If you only forced it through i rotation (probably only 180 degrees) then it won't be more than 2 sets damaged (off the top of my head).

You might as well replace all the guides as you will have a fully rebuilt head then , and if you are going to chase some performance down the track get the head lightly ported while it is off. The valves will be the expensive bit (i suspect). Just to give you an idea i ordered a full set of guides form my CA for $120 + postage from the states.

Yeah ok, guess I'll give it a crack... The compression test will me how many sets are gone... I'll just pm you when the head comes off as to what I'll need, fairly upsetting cox it's my daily!!

Pull all the plugs as well. Take the fuel pump fuse out and unplug the injector loom.

If you only forced it through i rotation (probably only 180 degrees) then it won't be more than 2 sets damaged (off the top of my head).

You might as well replace all the guides as you will have a fully rebuilt head then , and if you are going to chase some performance down the track get the head lightly ported while it is off. The valves will be the expensive bit (i suspect). Just to give you an idea i ordered a full set of guides form my CA for $120 + postage from the states.

a leak down test would be 100% accurate.

either way.. a breakerbar on the crank is a no no with no timing belt on.

yup means valve has hit a piston, and been bent from the forces exerted on it

as per sms Ive got a set of Neo intake/exhaust valve seats for you here, brand new

As topic says, I rekn I've bashed up my valves, will the car start with them bent? I thaught no due to nonconpression, but the car does start... Super raggedy tho!

chef have u still got that timing belt n stuff for sale ???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...