Jump to content
SAU Community

Looking For Lower Seat Than Gt-r Seat

On Edge

By On Edge,
in Motorsport Discussion & Builds

 Share

Recommended Posts

On Edge Veteran

On Edge

Posted
Posted

hey people,

i currently have nismo 400r seats in my r33 an would like to buy a fixed bucket seat for holding, as well as having a lower seating position.

my question is do most fixed back seats sit lower than the GT-R one? An if so by how much

Any help would be much appreciated

phunky_monkey Grand Master

phunky_monkey

Posted
Posted

The lower seating position is usually achieved by the rail rather than the actual seat itself. If you want to go low and don't want to go custom, I'd suggest a Bride Super Low rail teamed up with whichever seat you like (and that fits).

On Edge Veteran

On Edge

Posted
  • Author
Posted
The lower seating position is usually achieved by the rail rather than the actual seat itself. If you want to go low and don't want to go custom, I'd suggest a Bride Super Low rail teamed up with whichever seat you like (and that fits).

thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

FineLine Grand Master

FineLine

Posted
Posted
thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

Thats the exact combo i am using and yes it is lower than the 33 gtr seat. I have the gtr seat as a passenger seat and there is a noticeable difference in seat height.

  • Nope 1
phunky_monkey Grand Master

phunky_monkey

Posted
Posted
thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

What rail is it?

Yes the seat is chunky, but I'm telling you that 90% of the height difference will be in the choice of rail.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yep, rail design is the key. sometimes you will need a base plate to provide a flat surface, then bolt sliders to that so seat can move back and forward and then you bolt your side mounts to the sliders and the seat to the mounts. with all that stuff you end up with a fair bit of height. removing the sliders gives back about 20mm or so maybe even 30mm depending on design. you do still need some kind of base plate though to give a level mounting surface for the side mounts. the other option is modify the floor to allow you get a flat frame for the seat nice and low. lot of work though and must be done professionally.

phunky_monkey Grand Master

phunky_monkey

Posted
Posted
the other option is modify the floor to allow you get a flat frame for the seat nice and low. lot of work though and must be done professionally.

I had this done in the 180, and although it was pricey my shoulder now lines up with the door frame and I'm 6'4. Super low!

Having said that, a good Bride super low rail will drop you significantly for around $300. The drop depends on the car; in the 180 it was great until I got the cage which obstructed my seating position. In the STi I sit even lower than the 180 with the modified floor (feels that way anyway). Ridiculously low at it's lowest setting, but three heights to choose from.

Buddhz Apprentice

Buddhz

Posted
Posted

So which bride rail did you have before you modified your floorpan Dane?

Was it low enough for you to wear a helmet without the cage?

I have a bride rail with an older model Profi SPG in my S13 atm (its not the lowest one) and with a helmet my head hits the roof. I'm only 6' as well which is strange - maybe my body is out of proportion :(

phunky_monkey Grand Master

phunky_monkey

Posted
Posted

It may be mate! :(

I think it was an FO, and I fit with just enough room though I'm 4 inches taller than you. That's with an SPA so much of a muchness.

In the STi I have an FG and it is super low, so I'd actually suggest trying one of those out.

FineLine Grand Master

FineLine

Posted
Posted
So which bride rail did you have before you modified your floorpan Dane?

Was it low enough for you to wear a helmet without the cage?

I have a bride rail with an older model Profi SPG in my S13 atm (its not the lowest one) and with a helmet my head hits the roof. I'm only 6' as well which is strange - maybe my body is out of proportion :(

mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

  • Nope 1
On Edge Veteran

On Edge

Posted
  • Author
Posted
mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

thats where im buying my seat an the rail im looking at using, did you have much trouble with installation?

FineLine Grand Master

FineLine

Posted
Posted
thats where im buying my seat an the rail im looking at using, did you have much trouble with installation?

None at all, when I got around to doing the cage I had to cut the rail that seperates both side rails so the seat could go down a slot or 2. Its pretty basic stuff mate.

  • Nope 1
phunky_monkey Grand Master

phunky_monkey

Posted
Posted
mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

I have a generic type base rail with RPM side mounts in my passeneger seat, check the height difference out. That's without sliders too.

BUT I didn't cut the middle out to drop it, don;t think I can with the width of the SPG-N.

post-8405-1281065615_thumb.jpg

FineLine Grand Master

FineLine

Posted
Posted
omg thats great :( sorry to be a pain but how much do you reckon the driving height would have been lowered from a GT-R seat?

wish my car was here and not at the workshop so i could actually go measure.

From memory about 25/30 mil. You can also rake the seat back a bit to give yourself more head room by going to a lower slot on the back.

  • Nope 1
FineLine Grand Master

FineLine

Posted
Posted
I have a generic type base rail with RPM side mounts in my passeneger seat, check the height difference out. That's without sliders too.

BUT I didn't cut the middle out to drop it, don;t think I can with the width of the SPG-N.

I see what you mean phunk. That rail is a different animal to mine. Mine is actually a slider and is way lower than that puppy.

  • Nope 1
On Edge Veteran

On Edge

Posted
  • Author
Posted
wish my car was here and not at the workshop so i could actually go measure.

From memory about 25/30 mil. You can also rake the seat back a bit to give yourself more head room by going to a lower slot on the back.

yeah tru that, beautiful cant wait to get it, do you remember what the name of the rail was?

FineLine Grand Master

FineLine

Posted
Posted

Now that I cant help you with. what I can tell you to assist with I.d. is that it has a lever on either side of the rail with a brass knob on the end. these levers are lifted to the verticval position to slide the rail and back to the horizontal to lock it in place.

  • Nope 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...