Jump to content
SAU Community

Gtr + Other Parts Clean Out


Recommended Posts

About to sell my R32 GTR so these parts are no longer needed

All parts are located in the Parramatta area, will post also at buyers expense.

Please look at the pictures carefully for condition of each item.

Either PM or call me on 0411 352 888 if you're interested in anything.

1: RB26 timing cover, painted in a custom purple. Immaculate finish.

Also because it's already been prepped smooth and painted, would be very easy to paint it to the colour you choose without much prep work.

$65

2djxfzo.jpg

2: Brand new RB26 Gates timing belt. Bought this but never installed it.

$95

6hm6go.jpg

3: 30mm wheel spacers with all nuts and a set of locking nuts included. 5 x 114.3 stud pattern

Used but in very good condition, was only on the car for 3 months.

$145

2u56h5w.jpg

4: Momo sports steering wheel and R32 boss kit (compatible with HICAS). Has a crack on each side of where your thumb goes.

$80

2qmj9c6.jpg

5: Isotta steering wheel, in good condition. The thumb grip on the left had side is slightly peeling, however a bit of glue should fix that.

$90

jajrb8.jpg

6: A set of R32 GTR headlights in excellent condition. All clips and mounting points intact.

$185

dha104.jpg

2vufspg.jpg

1zclgxx.jpg

7: Standard R32 GTR ECU in working condition. Not needed as I'm running an Apexi

$50

2mcx2yq.jpg

24fjorc.jpg

8: Blitz induction pipe and pods. In great condition, I had the pipe painted in silver. Comes with brackets.

$145

1zefuzb.jpg

9: Mats from an R32 GTR. Unfortunately I have misplaced the driver's side mat, but I was using the r33 mat which actually fitted better, although they do miss match in colour.

No rips, tears, slight fraying to the borders.

$30

330fbyh.jpg

10: R34 mat set, in excellent condition. The only wear is slight in the heel patch, which you can see in the pic. Other then that the mats are in great condition.

$95

epere0.jpg

Link to comment
Share on other sites

  • 3 weeks later...
  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Took a little trip  went to nismo hoping the get my fuel tank hoses and unfortunately they told me they didn’t have stock luckily I was able to go to a Nissan parts store and they were able to order them in for me  then can home and cleaned the tank with some degreaser and fitted the new hoses before putting it back in the car 
    • 100% I’ll hack into the 33. Strap a turbo onto the RB25DE and/or put the 25 head on a 30 block. 33 passed in cos the reserve was too high. I’ll try lowballing it again and negotiate. Aim is to have it landed and on the road for under 15k, then spend the same amount on top in mods.
    • It's generally best practise to run 1x run without VCT enabled, then 1x run enabled till redline. Overlay the two torque graphs and you'll find the desired RPM to turn off VCT. Sometimes, it might be even worthwhile turning off VCT earlier control torque/cylinder pressure and using VCT purely to spool the turbo.
    • They sell them in Malaysia for about $4
    • First time I ever have issues with Amazon, but my wife often tells me to keep an eye out for fakes. It finally got me. I wrapped up the conversation with Gates. The gentlemen I was talking to seemed to hate his job but the response time on their technical support is outstanding. He stated that the hose is marked with some variation of "SAE J30R10" but that if you only purchase a 1 foot length like I did, it is possible to get a cut between markings and have a blank hose. To no ones surprise, he stated the swelling and "gummyness" isn't normal and to replace/buy from somewhere else (He mentioned NAPA). I'll toss a small end of the new one in gas for a few days before pulling the hanger out again, just to be safe.  Hose should arrive Monday. For those running multiple pump in tank hangers, you know the joys of getting them out and back in. I'm surprised I haven't destroyed my level float yet.  Lastly once I wrap all of this up, I'm planning on hitting the dyno again in 2 weeks while I'm on vacation. I realized recently that my VCT is set to turn off at 5000RPM. I'm surprised it wasn't increased while I was on the dyno last. I'm expecting I can increase it to ~6500RPM, if not more. Should hopefully get another 15-20kw out of it. I also want him to revisit my knock thresholds. I'm occasionally getting false knock around 3000rpm. 
×
×
  • Create New...