Jump to content
SAU Community

Recommended Posts

Hi guys,

I have been searching and searching and looking some more for a set of dumps for my gtr. I am doing the turbos in the next few weeks (most likely finishing up in the next 2 months) and cannot find any decent dumps...

I am not chasing huge power - max 250rwkw as it is a street car and I want to keep high levels of reliability in it. I have been looking at Tomei, HKS and HPI dumps but all are going for circa $1k - well above what I want to spend on dumps at this stage.

Question is - has anyone tried opening up the standard r32 dumps by porting? Is there such a huge difference between the r32 and r34 dumps (well enough that it couldnt be remedied with some hours with a die grinder? I have no qualms taking to them with a die grinder and have done basic port matching before.

Thanks for your thoughts.

Link to comment
https://www.sau.com.au/forums/topic/334152-bnr32-dump-mods/
Share on other sites

Factory R34 dumps, even R33 dumps will do 350rwkw without a problem. R34 ones i've seen basically get to 400rwkw without a problem.

R32 are a bit more restrictive, but given the power you want is the same as what stock turbos could do... i doubt you'll get much value of out spending $500+

If anything just get R33 dumps, will cost you what, $50 and no time taking meat out. :D

All grinding them is going to do is weaken them anyway.

I run factory R33 dumps with my HKS GT-SS, make 280rwkw @ 15/16psi with response/results exactly idential to those with big aftermarket items fitted.

Link to comment
https://www.sau.com.au/forums/topic/334152-bnr32-dump-mods/#findComment-5414587
Share on other sites

Indeed. I have bought one of the kits of ebay and will rebuild them myself and then have them professionally balanced.

I know its not the best option compared to say a set of -9s, but it'll be a good experience and suit the amount of power I am looking for.

Link to comment
https://www.sau.com.au/forums/topic/334152-bnr32-dump-mods/#findComment-5414615
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...