Jump to content
SAU Community

Recommended Posts

Nismoid the Garret turbine maps actually show the flow rates of the 0.82 GT30 and the 0.63 GT35 as having similar maximums though IMO the GT30 0.82 is the better map , these are with the T3 flanged GT30 turbine housings BTW because the 30 and 35 both use them .

True, they would be close.

However he wants to chase more power so I'd be dubious as to wether it'll get any better.

Going up 100hp in comp size/flow, but down in turbine housing size... Can be a nasty mix.

25psi is still in a respectable efficiency zone of the 82mm compressor. It's out of the most efficient zone but still ok. Peak flow here is caps out at a touch over (60lb/min) , or almost 600hp before hitting choke.

If you use 90% of that flow then it equates to 440 to 450rwhp (assuming you had a larger engine). With 25psi as you stated you should get 410rwhp.

Can a 0.82A/R turbine flow this 410hp? Perhaps. You should check exhaust gas temps as you raise boost.

You probably won't need a bigger compressor just a bigger turbine (and total flow, so you'll also need a GT35 0.82AR). I'd guess a touch under 10% more lag ~400rpm, since you are only changing the turbine side to ~15% more flow. Why not have a look at the maps using true GT35 (3582) turbos and compare.

Edited by simpletool

thats all very interesting, as we all know the old faithful 20 is not the best choice for power, but ive always wanted

to know just how much a 2o can make when its a built engine, i think the limiting factor will be the valves and ports

buts that when the nitrous will come into play.

do you think i should remove the 26 intake and tb's and go for a longer runner and larger 8omm tb option.

i had never thought about a td series turbo, always thought they were a bit old school with response. maybe a BB TO4Z?

How would my 3040 with a 1.06 rear housing compare to a 3582 with a 0.82 in hp rating and response?

I can handle another 500rpm of lag if it means the possibility of making my power goals.

Edited by boostn32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...