Jump to content
SAU Community

Recommended Posts

Hi guys, i always thought there was a bit of a problem with my r33 s1 gtst but i confirmed it tonight. Ive had it for a few months now and its been this way since ive had it. It seems no where near as responsive as it should be, the power is there... eventually but most of the time it feels like im driving a 1.6L pulsar until the boost comes on.

The car is stock and tonight i took my mates 180sx out for a drive which is also stock.

WOW... His car feels so much faster then mine, when i put my foot down it actually goes somewhere, i feel so ripped off. I was in 3rd and the wheels started spinning, thats never happened to me in 2nd gear.

At first i thought my clutch was slipping but a mechanic mate told me how to test that and it seems fine.

Also the car seems like its going off its head, like its working way too hard at higher rev's, ive watched vids of stock r33's and they sound good at high rev's where mine sounds like the pistons are about to punch right through. The oil gauge never drops below 4kg per inch or watever it is either.

Any ideas?

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/335666-r33-gtst-power-issues/
Share on other sites

The only way to know for sure would be to remove the turbo and have a look. Or possibly check the cat convertor and see if its damaged inside or has any extra bits in there. Im sure some of the guys on here that started with stock 33s would know more.

Ive never driven a stock 33 so dont know what they are like with stock boost and response. Mine had a TD06 with 245rwkw when I bought it.

how accurate is a digital Tacho? Ive got one in my turbo timer which is showing waaaay different to what the dash tacho is showing , could explain why at 4k in dash tacho it sounds nuts.

Firstly my understanding is the car is meant to idle at 650rpm? indash its showing idle of about 1000 rpm and the turbo timer is showing it as 1650rpm when i rev is a bit to 2k indash , its shown as 3k in the turbo timer tacho.

Mayve the car is lacking torque. What would cause this?

Edited by XeKayeM
wouldnt that effect the idle aswell though? because it idles smooth

Not necessarily. :P

You don't need to pull the turbo off to check the blades, just pull off the dump / front pipes.

Stick with the factory tacho, if it is reading 1,000rpm then something is wrong bringing up the idle (air leak) or you need it adjusted.

if the turbo timer is setup wrong then it will show your rpm being different to the dash.

as for the idle at 650rpm, that all depends on whether the air con is on or not, as well as the temp of the car. it will idle higher when it's cold.

for the power bit, your mates 180sx spinning the wheels in 3rd doesn't mean it's much more powerful, just has crappier tyres, especially if the car is stock. they also do feel a bit faster than a 33.

there are a few things you can do to find some possible causes of your issue. first, what rpm are you making full boost? with the stock turbo at 7psi it should be making full boost by well under 3000rpm. if it is higher than that then you either have an issue with the wastegate or it could also be caused by timing or fuel issues. secondly get a timing light and check the timing. if this is too retarded then you will have poor performance and advancing it a bit can make a world of difference. thirdly, if you still can't find any issues, take it to a workshop and put it on a dyno. this will tell you what power it's making and what the air/fuel mixtures are like. if the timing is fine and the AFR's are fine and it's making low power then more than likely it's just your engine that's stuffed. getting a compression test done would tell you whether it is or not.

it could be a few other things though. the cat converter could be blocked, the air filter could be crappy, the afm could be stuffed, the timing belt could've jumped a tooth, and many others. might not even be engine related. might be that you have brakes that are sticking on, or tight wheel bearings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi Apex and welcome! 
    • Probably too late to reply to this, but worth a try. It's not calliper flex, the calliper as a whole is moving so it has to be calliper mounting bracket flex.  Calliper mounting brackets are designed to stop the calliper rotating, they don't need to be designed heavy duty to stop the calliper moving in and out.  Whatever it is is not the major cause of poor pedal feel, the outer pistons are moving towards the disc rotor the same amount as the inner pistons are moving away from the disc rotor.  Hence no change in fluid usage, what extra fluid is needed to move the outer pistons is recovered from the inner pistons. For a calliper to move as a whole by far the most common reason is the rotor is not perfectly centred in the calliper.  The first thing I check is that hub face is perfectly clean, bare metal, where the rotor hats contacts it.  Then I check the that rotor is firmly held in place by at least 3 wheel nuts (or equivalent). If all of the above are confirmed to be in perfect alignment then I would check the piston sizes and ensure that the 3 inner pistons and 3 outer pistons have matching diameters (eg; 28/32/36mm).  I have seen a no name 4 spot calliper that had 1 of the 4 pistons a different diameter. Maybe I missed it, are both the callipers exhibiting the same problem? I would remove the transfer pipe and inspect it to make sure that there are no restrictions. Maybe you already have but if not I would return them with the video and have them confirm all of the above.   Hope that helps Cheers Gary    
    • If you have the original log book and it didn't have a chassis number quoted, then no money required.  I have "rechassied" a number of race cars, no problem as long as you have the original log book.   Cheers Gary
    • Well the good news is that it won't run any worse with an atmo bov than it does with no bov, I've owned a few Nissans over the years (r32, s15 and now r33), the stalling issue caused by a bov or no bov while still having an afm is easy enough to live with, most people get used to driving them and just feathering the throttle when you come to a stop to avoid it stalling. Changing to a proper ecu with a map sensor is ideal but in the short term I'd just slap in the bov if you really want the whoosh sound. I looked into the pass through type maf like the R35 one above but decided against it as the amount of oil and crap flowing through the hot side would mean you'd have to clean it often to keep it working.
×
×
  • Create New...