Jump to content
SAU Community

Recommended Posts

Hi guys, i always thought there was a bit of a problem with my r33 s1 gtst but i confirmed it tonight. Ive had it for a few months now and its been this way since ive had it. It seems no where near as responsive as it should be, the power is there... eventually but most of the time it feels like im driving a 1.6L pulsar until the boost comes on.

The car is stock and tonight i took my mates 180sx out for a drive which is also stock.

WOW... His car feels so much faster then mine, when i put my foot down it actually goes somewhere, i feel so ripped off. I was in 3rd and the wheels started spinning, thats never happened to me in 2nd gear.

At first i thought my clutch was slipping but a mechanic mate told me how to test that and it seems fine.

Also the car seems like its going off its head, like its working way too hard at higher rev's, ive watched vids of stock r33's and they sound good at high rev's where mine sounds like the pistons are about to punch right through. The oil gauge never drops below 4kg per inch or watever it is either.

Any ideas?

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/335666-r33-gtst-power-issues/
Share on other sites

The only way to know for sure would be to remove the turbo and have a look. Or possibly check the cat convertor and see if its damaged inside or has any extra bits in there. Im sure some of the guys on here that started with stock 33s would know more.

Ive never driven a stock 33 so dont know what they are like with stock boost and response. Mine had a TD06 with 245rwkw when I bought it.

how accurate is a digital Tacho? Ive got one in my turbo timer which is showing waaaay different to what the dash tacho is showing , could explain why at 4k in dash tacho it sounds nuts.

Firstly my understanding is the car is meant to idle at 650rpm? indash its showing idle of about 1000 rpm and the turbo timer is showing it as 1650rpm when i rev is a bit to 2k indash , its shown as 3k in the turbo timer tacho.

Mayve the car is lacking torque. What would cause this?

Edited by XeKayeM
wouldnt that effect the idle aswell though? because it idles smooth

Not necessarily. :P

You don't need to pull the turbo off to check the blades, just pull off the dump / front pipes.

Stick with the factory tacho, if it is reading 1,000rpm then something is wrong bringing up the idle (air leak) or you need it adjusted.

if the turbo timer is setup wrong then it will show your rpm being different to the dash.

as for the idle at 650rpm, that all depends on whether the air con is on or not, as well as the temp of the car. it will idle higher when it's cold.

for the power bit, your mates 180sx spinning the wheels in 3rd doesn't mean it's much more powerful, just has crappier tyres, especially if the car is stock. they also do feel a bit faster than a 33.

there are a few things you can do to find some possible causes of your issue. first, what rpm are you making full boost? with the stock turbo at 7psi it should be making full boost by well under 3000rpm. if it is higher than that then you either have an issue with the wastegate or it could also be caused by timing or fuel issues. secondly get a timing light and check the timing. if this is too retarded then you will have poor performance and advancing it a bit can make a world of difference. thirdly, if you still can't find any issues, take it to a workshop and put it on a dyno. this will tell you what power it's making and what the air/fuel mixtures are like. if the timing is fine and the AFR's are fine and it's making low power then more than likely it's just your engine that's stuffed. getting a compression test done would tell you whether it is or not.

it could be a few other things though. the cat converter could be blocked, the air filter could be crappy, the afm could be stuffed, the timing belt could've jumped a tooth, and many others. might not even be engine related. might be that you have brakes that are sticking on, or tight wheel bearings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...