Jump to content
SAU Community

Recommended Posts

Hello everyone,

Up for sale is an suitcase sized assortment of stuff brought back from my time teaching in japan and some leftover bits collection.

Z32 300ZX AFMs

All were purchased from parts companies in japan and described as tested/working. They are all JECS made in japan, factory AFMs not the no brand generics that come up from time to time.

2 have damaged mesh - $100 each

1 looks perfect $150

1 with HKS airpod and plug (was fitted to a R32 GTS-T) $200

2 spare plugs if needed $10 (with an afm)

post-21158-1283689769_thumb.jpg

CUSCO caster rods:

R32 GTR pair, perfect condition (fits GTS-4 but NOT other skylines)- $200

post-21158-1283689745_thumb.jpg

R32/S13 2nd pair, they are in good condition but have some black overspray on them (scraped a bit off with my fingernails so can be cleaned up if its an issue) $180

ran a check on the part no and the following came up:

Brand : CUSCO

Product: Adjustable Pillow Ball Tension Rods Nissan

Part Num: 220 473 AS (RS13,RPS13,S13,PS13,HCR32,Y32,A31,Z32,C33)

post-21158-1283689696_thumb.jpg

Please email if you need me to take measurements to check if they fit your car.

R32 Rear bumper lights, perfect condition (sides of the number plate, i think they were from a 32 GTR?) $75 the pair

post-21158-1283689789_thumb.jpg

Triple gauge clusters for dinn slots - bought a bunch as they are nice and small for the suitcases!

R32 GTR $50-$100 (lots of different conditions please email for close ups of the lot) also have connector plugs with a bit of wire on them for some if your doing a custom install in a different car.

R32 GTR BRAND NEW front covers for the triple clusters $35 ea

R33 GTR $120- all in good condition (these have a carbon fiber style front and a torque split gauge for the AWD)

R34 GTT (NOT for a dinn slot!) these sit on top of the dash and would suit a custom install or replacement

Gauges $80

Guages cover/surround $100

post-21158-1283689806_thumb.jpg

R32 GTR brake calipers (full set) $300 - pads included but about 50%ish I have a brand new set of front pads if required.

post-21158-1283689926_thumb.jpg

Z32 brake setup - complete and still on my 300zx wreck, included calipers, pads, rotors and lines if needed. pads in great condition. $400 the lot

BOVs

HKS (and SR20 DET pipe) $120/$30

BLITZ in box, fitted for a short time only to a soarer) $160

post-21158-1283689720_thumb.jpg

also R32 GTR indicators from $75ea (already advertiesd in an earlier posting), S13 bits including type X light, steering wheels, TIEN suspension, and more random stuff) ill add bits as i go through the garage.

Postage:

Pickup is welcome from Kyogle 2474. Or i can post, Registered only.

Please email or PM if you would like close up photos of anything.

Martin Marschall,

[email protected]

(02)66333131 (best in the evening)

Thanks for looking! :D

  • 3 weeks later...

GTR Cusco rods now sold, S13 suspension sold and 2 of the GTR triple gauge font covers sold (1 remaining is available again, buyer never replied).

Everything else still here. :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...