Jump to content
SAU Community

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

How many people actually got fined for $10,000? Can anyone provide details as to why they got fined $10,000? Is that a fine from the cops or from EPA? Was it on the spot or when you're going through the pit?

http://www.boostcruising.com/forums/index....0225&st=150

But again like everyone said, its not worth the risk with the amount of gain. I just asked the question out of curiousity as I reckon that kinda fine is a bit ridiculous especially when a defect fine is only $100.

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5435627
Share on other sites

So many people de-cat their imports....i just had the standard cat in there, unbloted it, bashed the guts of the car out with a screwdriver and put the cat back in. Made massive flames, like 2m long bright orange flames lol

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5435957
Share on other sites

harden up and run he de-cat- more power, a shitload cheaper and better turbo response

yes apparently its a 10k fine but how can they find out? we dont have EPA in perth

even then is a copper really gonna stick his head under your car? even then hows he gonna see if u've got a gutted cat they dont carry infared thermometers all they can do is 'suspect' u have no cat and then give u a yellow. if u go over the pits with a decat/no cat then u deserve the 10k fine, after u get a yellow u got shitloads of time to take it off.

it was said before, whos actually been done for not having a cat (in perth anyway)

-ive got a 3inch straight through pipe which has had a standard cat chopped in half and welded around it (cat temp sensor still screws into the shell) for sale as my cars written off u wanna buy it PM me (btw this was used for the track only not on the road)

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5436929
Share on other sites

Go run a GRiD backfire with decat in front of a cop car, and get back to us on your "yellow" sticker with a shitload of time before expiry....they can (and have done previously) given as little as 15 minutes on yellow stickers).

You'll get a RED sticker for that shit.

And EPA isn't necessary to get you into shit over here, go give it some juice at night time......we've all seen a de-cat'd car give it some juice at night, and the sudden bright flashes it can cause....that shit can cause short and/or long term damage to vision.

De-cat's are a stupid idea, they do f**k all for performance. 7hp, and what do you get? You can't have a decent conversation in your car, which you have to clean weekly thanks to unburnt fuel being all over the back of it.

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5437256
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...