Jump to content
SAU Community

V36 Factory Cruise Control

katstudios
 Share

Recommended Posts

DashyyPC Collaborator

DashyyPC

Posted
Posted
On 3/11/2019 at 3:09 AM, Chris Rogers said:

you do need other parts. call the number I gave you and tell them you want them to install a cruise control for this car. tell them you have OE controls and need them installed as well.

 

this IS NOT a DIY job.

Sorry to bother you one last time.
We're about to do my mates who has a steering wheel from a 09 v36 SP so has the buttons.

I can get a 2013 G37 Steering wheel with the buttons (slightly different on/off location) and has the one extra tab and wires on the back. The one from the v36 only has the one clip for all the buttons i think.
Do you you have any idea weather the steering wheel pictured below from a 2013 would be ok to utilise the OEM buttons?

s-l1600.jpg

DashyyPC Collaborator

DashyyPC

Posted
Posted

Looks like it might not. The G37's seem to have 2 clips and everything i find on a v36 Seem to merge into the one clip.
I think using Part number 25550JK15A i could just replace that centre unit and the wiring on my current wheel.  

  • 1 month later...
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

I pulled the center out of a fair few of those. I got to a point that I found the OE number for that bit and the correct controls (of which there are 3 types.)
no longer have the part numbers handy.

  • 1 month later...
-NismoR32- Rising Star

-NismoR32-

Posted
Posted

Cheap if anyone looking for an aftermarket one  

 

https://www.gumtree.com.au/s-ad/mount-waverley/other-parts-accessories/cruise-control-for-a-v36-skyline/1220948953?utm_campaign=socialbuttons&utm_campaign=socialbuttons&utm_content=app_ios&utm_medium=social&utm_source=ios_social

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...