Jump to content
SAU Community

Recommended Posts

Hi,

Items are located in Sydney's West.

NEW R32/33/34 GTR upper radiator bushes set of 2 bushes $20 delivered

NEW OEM Top Injector o-ring set of 6 $50 delivered

NEW Yokohama A-Drives set of 4, 265/35/R18 $1200 for the set.

NEW The SARD M.F.C. (Multiple Fan Controller) $170. Got a haltech so no need for this anymore.

Never used or installed HALTECH IQ3 Display Dash - Reads Vnet Sensors and includes Internal CAN Interface Module to read Haltech ECU info/sensors $900

LS1 coils, leads and brackets (mounts above injector rail) $700.

R33 GTR front Guards and raisers. $550 in silver.

R33 Series 3 Xenons, near new. not seen any road kms..

Cheers,

Johno

$2400 for the lights, they are near new. only fitted to the car and litterally run on the dyno and towed home. The lights were purchased from RHD Japan. They are now on there for a whooping $4105 delivered to OZ!

http://www.rhdjapan.com/bcnr33-kouki-xenon...eadlights-12139

I have a bad habit of buying parts then falling short of $$ for the home loan lol.

Cheers,

Johno

do the guards come with the side skirt addons and can I see the pics of them?

If so price to Mansfield, QLD 4122

Pics of guards attached raiser are not in the pic but are included. Side skirt add on is not included.

Pics of Yoko's too

pics of coils plz

This is the only pic I have of the coils at the moment, I'll dummy fit it over the weekend to show how it all fits and looks. It is similar to the 101 imports gtr set up but not as neat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
    • Well, yeah. But I just expect everything other than my car to feel like a bucket of shit anyway. I still miss my Alfa 116 so much though. You could run over a 20c piece and tell whether it was heads or tails.
×
×
  • Create New...