Jump to content
SAU Community

Recommended Posts

rb25det power fc, 6 months old $1800

z32 air flow meter (almost new 3000kms) $200

gcg stainless steel high mount manifold t3 flange $500

garret gt3540r .63 rear houseing almost new with only 3000km's on it $1800

turbosmart 45 pro gate $500

custum dump/front pipe $250

would rather sell as package is making over 400rwhp on 14psi safe tune

................................................................................

.............................................

rb20det stock exhaust manifold and turbo (good working condition

with no shaft play) $300

stock rb20det plenum with tb $100

rb20det motor was running but not healthy (needs water pump) $200

3" catback exhaust with cat $100

stock r32 gst seats good codition $100

s15 bride door trims $400

extra pics to come.

post-47384-1286090266_thumb.jpg

post-47384-1286090503_thumb.jpg

post-47384-1286091089_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/339043-rb25-and-rb20-parts/
Share on other sites

Where you located? Keen on motor

sorry

located in wingham nsw 2429

just letting you know, the motor is bare

5ky whats you offer on just the commander

Edited by stewari
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...