Jump to content
SAU Community

Recommended Posts

  • Replies 172
  • Created
  • Last Reply

Top Posters In This Topic

most half cuts go for 2500 ( r33 ) but not stagea half cuts.

u say 1500 but thats for a r33 motor, box ect not a s2 awd stagea that has a r34gtt rb25.

price is good i think

Edited by whitenight27

haha true true too much boost.

i shore goodo thinks its worth what his asking for.

the extra 1000 is because its a r34gtt and not a older r33 motor.

for 1 the turbo is a lot better than the 33.

the 34 turbo can run little more boost and has a bigger rear housing but still responsive

33 turbo has a ceramic compressor wheel while the 34 turbo has nylon compressor wheel and better for hi-flowing

i will just say don't think u will ever get a 34gtt motor ecu and piping for 1500. r33gtt yer no probs

34 will have low ks and a lot newer motor than a 33 rb25

Edited by whitenight27

whiteknight27you will have to be a little more clear when you say what is left. I prob dont have much that you need but if you ask for what you actually need i will be able to answer yes or no . As for the 34 front it went on to my new one

menthol369 sorry but the motor is gone got $2300 motor loom and ecu

thort u would get around 2k for it lol.

any how need things like

peddle box

console

hand brake and cable

any thing i would need to change my auto 2 man

I belive i do have the peddle box and clutch master cylinder but i think thats about it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Your other option is to buy a spray can of hi-fill and prime it with some pinholes. See if the primer makes them disappear. If it does, then you can leave it with pinholes of that size and they will go away when the painter takes over.
    • Ah ok. I seem to be mixing it like everyone else does so not sure what's happening. Will experiment with it more.
    • Depends on what you mean by OK. First up, was this done cold or hot? Are they reasonably consistent? Yes, they are reasonably consistent. Could be better. But unless it has had a build at some point, it is a ~30 year old engine and you'd expect some variation. Some of the difference could also be in user technique Is it good compression? Well....not numerically, no. New they were >160 psi. The one at 140 would be fine, in that context. If they were all ~140, you'd be reasonably happy. But the one that is @120 is twice as far down from the original numbers as the one @ 140. But.. (again)... technique can play a part in the absolute magnitude of these numbers, and the quality/state of repair/accuracy of the pressure gauge is not known. In the context of the above, the compression tester that was used last on my car is regularly compared to a known good pressure gauge. Not calibrated, exactly, but compared to a reference instrument that is not used for any other purpose, so cops no abuse. So we can trust the measurements off that tester. But another tester in the same workshop wasn't being compared against the standard and was reading a good 30ish psi lower. When you're reading 100 psu but the engine is really doing 130, you can make bad decisions.
    • More likely from tiny bubbles in the filler/putty. Maybe be less aggressive when mixing it. Perhaps invest in a vacuum chamber to pull the air bubbles out?** **I don't know if this is a thing for body filler. I see hardcore epoxy makers degassing their mixed resin on the regular.
    • IIRC, the speedo on these is fed from the sensor in/on the snout of the diff.
×
×
  • Create New...