Jump to content
SAU Community

Recommended Posts

Heya Guys,

Me and my mechanic have been mucking around a bit with timing and throttle control coz in the morning i have to put my foot down on the accelerator for about 5 secs until it comes back to the correct idling. The revs first thing in the morning are really low so much so that it just about conks out on a start in the cold morning. We put my timing up and now the idling is revving at 750.

Any of you guys able to tell me what your idling is revving at?:confused:

Link to comment
https://www.sau.com.au/forums/topic/3401-for-those-with-apexi-safc/
Share on other sites

When dead cold mine idles around 1200 then settles to 750 once warm. 25GTT did the idle play up once you had the SAFC fitted/tuned? Coz the SAFC shouldn't effect idle unless you've mucked around with the (DEC-AIR) which I think is only used if your BOV is venting to atmo.

Originally posted by rs73

On cold start mine will idle at more than 1000rpm, perhaps like 1200rpm if I remember.

Once the engine is warmed up, it idles at around 650rpm to 700rpm.

isnt this because of the auto choke?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
    • Being a manual, we very quickly ordered new R34 gearbox (From Nissan) and remaining parts from Kudos motorsports. Would highly recommend the team there. Ultra helpful and quick to share advice and upgrades. We are in the middle of taking the Auto out (Genuine 94,000/kms) and putting the Manual in this weekend. Part 2 of the build will include likely a Plazaman Intercooler and Plenium, Hks Exhaust with Tomei Dump (ordered).
×
×
  • Create New...