Jump to content
SAU Community

E85 At The Pump Yet?

zebra

By zebra,
in Australian Capital Territory

 Share

Recommended Posts

Trozzle Grand Master

Trozzle

Posted
Posted

I've not been past Kambah to have a looky, but Pat checked out Nicholls (northside servo) not long ago, and they said there was an engineer out there checking out the pumps to make sure it'll be all good.

Trozzle Grand Master

Trozzle

Posted
Posted

Exactly. Haven't plenty of people including Trent (STATUS) mentioned you won't gain any more power past a certain point of ign timing on an E85 mix anyway? If you're running it in a street car, particularly a daily like mine, conservative tuning is the way to go. Go close to the edge with 98 mix, then back off the timing (particularly up top) and add a touch of fuel. Would rather feel the torque from E85 than see what kind of top end figure I can pull.

natett Proficient

natett

Posted
Posted

ill have to check a few things about it problem with my setup (apart from the need for additional pumps) is my 1000cc wont cut it lol would be fun to have a gt42 on street tuned 30psi though haha not sure if the motor will last too long though haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
    • GTSBoy
      R34 manual conversion speed signal wire finding, need help

      By GTSBoy · Posted

      Yes. Autos typically work from the speed sensor on the pinion shaft of the diff. I also think that even if you have a proper speed sensor for the bog manual in the manual box, that the signal it outputs is not compatible with the auto dash anyway. You should consult that manual (the book, not the gearbox).
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      And I just realised that that advice is slightly nonsensical for a GTR, because you need 2 of them. But it is otherwise true.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Having had a reasonable look at the car, I'll be able to remove the (one time) rams and retract the hinge (they are held in the down location by a tiny (m3?) sacrificial screw) which will get it physically back in shape. From there if you remove the rams you need a resistor to turn off the airbag light (as Mark said, there are plug in kits and I might go that way because its reversible). And...per all the threads on here, even if you have the resistors to turn off the airbag light, the bonnet light will stay on as it writes to the airbag computer history - that is either replace the airbag controller, reprogam the EPROM (if I can work out how), or remove the globe from the dash. Having seen how sensitive this system is, if I had my time over I'd pre-emptively remove the rams, even on a road car, because this is all a very unnecessary pain in the arse. Reminds me, time to go and have a look at the Fuga too....
×
×
  • Create New...