Jump to content
SAU Community

Recommended Posts

1. Evo 8 MR complete seats front and rear including rails. Not sure whether I would be bothered to put them on my evo 7, but if they dont sell, I'll put them em on. asking $1650 top condition!! Just got them all steam cleaned on 8 Nov 2010.

img0799.jpg

img0803r.jpg

img0805.jpg

img0806h.jpg

img0810o.jpg

2. Evo 7 GSR complete seats front and rear including rails. asking $1400 top condition!! Just got them all steam cleaned on 8 Nov 2010.

img0812e.jpg

img0814.jpg

Located in Melbourne near city.

[email protected]

0433552745

Gerald

Thanks

if you can organize courier then it's all good with me.

i'll pay $50 of shipping to help you out.

but cant really use auspost, they'll charge alot of $$$$$.

hope it sounds good to you mate

try:

e-go

pack and send

Northline freight

all depends where you are.

but it's pretty difficult to get measurement for the seats.

do you have any friends or know someone going from melbourne to your state? probably give him $100 to take these lol.

forgot to mention,

they are off JDM EVO 8 MR and JDM EVO 7 GSR, which mean high and tight proper bolsters UNLIKE ADM evos with fat guy low bolsters which is close to nothing at all.

they perform much much much better on tracks compared to those ones on australian evos.

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...