Jump to content
SAU Community

Wet Roads Be Careful

autoworx

By autoworx,
in Western Australia

 Share

Recommended Posts

Ten Four Grand Master

Ten Four

Posted
Posted (edited)
This is why everyone needs to get out on the skidpan so they know what to do when it rains.

On another note, 1800kg Luxo in the rain is hairy

Then you need new tyres.... Dads LS400 is fine on nexens...

On another note, sisters s13 with probably just illegal rears doesn't slide at all..... (Auto)

I swear auto's are safer than manuals in the rain...

Edited by Ten Four
FluffyDiceAndaV8 Community Regular

FluffyDiceAndaV8

Posted
Posted
Then you need new tyres.... Dads LS400 is fine on nexens...

On another note, sisters s13 with probably just illegal rears doesn't slide at all..... (Auto)

I swear auto's are safer than manuals in the rain...

Yeah I do need new tyres, the lack of LSD makes it unpredictable on top of the weight, still fun though

bubba Grand Master

bubba

Posted
Posted
Yeah I do need new tyres, the lack of LSD makes it unpredictable on top of the weight, still fun though

My wagon was open centre.. rather scary in the wet but 4WD made it a bit safer. Now, with LSD in 2WD, fun times. Need to get the bigger rear swaybar on, should make it a bit more slidey.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...