Jump to content
SAU Community

Recommended Posts

VG30DET Ball Bearing Turbo, actuator included, This turbo is from a single turbo 3.0L Nissan motor its much bigger than a turbo from a 300zx which is a vg30dett. Turbo has been checked out by garret and is still in good condition also comes with a high flowed front comp cover, rear back plate and a T04 Comp wheel, all ready to be bolted on. Asking $600 ono for the lot cheers

Link to comment
https://www.sau.com.au/forums/topic/34394-vg30-bb-turbo/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

I wouldn't say its a bolt on turbo unless the snout has been modified.

Basically the VG30 snout (compressed ait outlet) is dead straight. The RB20/25's require that the snout first go straight then do a 90degree bend, it then attaches to the IC piping. I poped down to AAA exhaust and had them make up a 90degree 2.5" bend. You are unable to use the RB20/25 turbo snout as it is smaller in diamater. I can't remember if it bolts up or not though. I bought mine for $600, went through 2 turbo's from the same jap importers. Both were stuffed. :rofl: Something to do with how they spray the crates hence moisture gets in to the bearings and rusts them.

ALso.. the VG30 Ball bearing turbo's came from the Infinity/Leopard VG30DET that made 190kw at the flywheel. Not the VG30ET from the old 300zx. Those turbo's are non-BB.

Link to comment
https://www.sau.com.au/forums/topic/34394-vg30-bb-turbo/#findComment-699491
Share on other sites

I took the turbo to two places, honeywell garret and j.c diesel which also repair turbos. Both comp-anys told me it was in good working order and it is a ball bearing item. In standard form is only good for 1bar maximum. Before i bought this turbo i rang at least 12 different places and only 2 places had one in stock. I got quoted $550 at one place and $770 at another. Some guy from this forum was going to sell me one for $900. As for documentation does it realy matter? it is a second hand item im selling and i have had it checked out by two different places. Price still stands at $500

Link to comment
https://www.sau.com.au/forums/topic/34394-vg30-bb-turbo/#findComment-699850
Share on other sites

GTST,

The oil & water lines don't have to be modifed IF the turbo is Ball Bearing.

There is one oil line that feeds in from the top of the turbo and a water line that feeds in to the turbo from the side of which the block is (its a bastard to do up as well).

Use the lines from your old RB turbo. Bolt up perfectly. As I said before the 'only' thing that has to be modified is the compressor's outlet so that it mates up with the IC piping.

Is there any chance of a pic from above to view the core? (inbetween compressor & exhaust wheel)

$500 is around the price peoples.

Link to comment
https://www.sau.com.au/forums/topic/34394-vg30-bb-turbo/#findComment-699997
Share on other sites

I had a look at the turbo and it does have an oil feed from the top etc. I know the series 1 rb25 turbo has 45v2 on the front cover. The main advantage of this turbo over the standard rb25 is that it has a slightly bigger ration on the exhaust housing, the guy at garret confirmed that for me. Thank you very much Joel for backing me up on price.

Link to comment
https://www.sau.com.au/forums/topic/34394-vg30-bb-turbo/#findComment-700533
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...